19 June 2016 1 9K Report

The equation for material loss calculation is..

ne=1.53*(1+x/R1)

na=1.0*(1+x/R1)

Here,in COMSOLE how I will find the value of X?

Thanks in Advance

More Md. Saiful Islam's questions See All
How to get onecolumn document from standard IEEE ACCESS LateX template?

I have prepared a manuscript in IEEE Latex template, but for some purpose, I need to prepare a word file as well (detailed format is not required). Compared to two column .tex file, one column...

02 March 2021 1,830 3 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

How does Scientist/RG community evaluates a case study article and the impact of it on a researcher career?

An article that is published as a case study in the SJR listed journal. How much value is added to a researcher career? How it is evaluated by a scientific researcher/University admission...

02 March 2021 9,661 3 View

What kind of food stuff increase the potentiality of human brain?

There are different kinds of food stuffs which we intake daily according to our requirements. Carbohydrate, protein, fat, mineral, vitamin, water are mainly working for the growth and development...

01 March 2021 831 2 View

What is the difference between L1 and L2 regularization in machine learning?

L1 and L2 regularization

28 February 2021 4,187 3 View

Can I put a figure that was drawn by Bio-Render in publication paper?

I want to publish paper in journal but I have figures which have drawn with bio-renders, can I put them in the paper or which other software I can use to draw them?

27 February 2021 8,179 1 View

How to add missing citation?

Dear colleagues, I have found that many authors have a concern regarding their missing citation in RG because often citation in RG is lower than google scholars. I also missed some citation...

26 February 2021 928 6 View

Can anyone suggest me the best way for Regression analysis of Accidents?

Dear Altruist, I want to make a regression analysis based on accident data. But I am not finding the necessary information about what type of regression is more applicable for analysis accident...

23 February 2021 9,956 3 View

How much cell pressure and back pressure should I apply to start for triaxial test for different types of soil?

We have recently purchased a triaxial test instrument (MATEST) for testing different types of soil. After installing software, we are facing a issue of saturation where the samples does not...

23 February 2021 7,194 4 View

How to assure whether a regression tree overfit or not by seeing bias-variance value of the model?

Lets consider a regression tree in which variance is 1.1065*e-10 and bias is 2.962e-13. Also the model RMSE on training set is 1.5e-5 and on training set is 1.2950e-5. Is the model is overfit or...

22 February 2021 7,755 2 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close