Export more than 2000 document information from Scopus?

Hi, I need to export information included in more than 150000 documents that belong to more than 250 journals from Scopus (in CSV format). However, Scopus allows to export only 2000 documents at a...

09 May 2020 4,633 3 View

Can I apply Kruskal-Wallis test?

I have a data set of 129 authors with different years of publishing experience and how importantly they consider the factor 'peer-reviewed' while selecting a journal to publish (these answers are...

12 February 2017 4,184 6 View

How to calculate how much reactant consumed (theoretically) when electrolysis was carried out for 10 hours?

When methanol-water (2M) electrolysis were carried out for 10 hours at constant current; how can we calculate how much methanol and water consumed theoretically?

13 September 2016 8,580 3 View

How to do Temperature ramping test using DMA Q 800?

14 September 2015 4,604 3 View

What is the best method to purify basic proteins with pi 7.8?

13 April 2015 5,256 5 View

Can anyone suggest if FEA or Finite Difference method is more suitable for the computation of heat conduction problem of a rotating cylinder?

31 March 2015 4,621 6 View

How can I increase the binding affinity of GST-tagged protein to GST sepharose column?

01 March 2015 7,678 4 View

Why is my protein getting precipitated, even at low concentrations?

I am purifying a recombinant protein (host Rosetta) with his tag. I am getting reasonably good yield (4-5 mg/liter of culture). However after affinity purification using Ni-NTA column, during...

19 June 2014 9,136 4 View

Can anyone help me figure out why I am losing protein during ion exchange chromatography?

I am purifying a protein from a bacterial system and I was able to successfully purify the protein through an affinity column. My protein has a pI of 5.9 and it is stable at higher pH. After...

01 June 2014 8,858 5 View

How much of Dnase can be added and what buffer can be used for cell lysis during protein extraction?

I am isolating protein from more volume of culture. However I am unaware how much dnase to use and also what buffer to use for its activity, if I am dissolving the pellet in 30ml of lysis buffer...

02 July 2013 7,943 4 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View