How to calculate the torque-speed caracteristique of a Synchronous permanent magnet Motor?

More Aissam Riad Meddour's questions See All

Is Genetic Algorithm usage for Motor Conception FEA optimization a good choice?

Hi RG community, Like the title shows ,i was wondering if choosing the GA for this kind of Optimizaiton is a good choice? For example we have a population of 100 (for 7-8 Optimization Variables),...

14 February 2021 1,160 7 View

How to Use Ansys Model into Simulink/Matlab?

Hi there, I'm trying to optimize an electric vehicle e structure (battery, motor, etc....), my battery model is on Simulink and the motor's is built using Ansys Maxwell I want to parallel optimize...

20 September 2020 3,331 4 View

Does insect such as flies and mosquitoes transmit the COVID-19 virus as a mechanical transmission?

Does insect such as flies and mosquitoes transmit the COVID-19 virus as a mechanical transmission? Virus transmission take place by insect legs, mouth parts and other body parts.

15 June 2020 6,000 98 View

Any feedback of SR protocols registration with INPLASY?

I've received an email today from a company offering to register Systematic Review/Meta-Analysis protocols with them. They offer DOI registration and unique registration under their database. Do...

14 March 2020 923 2 View

Is there anyone to help me get research on invertebrates that parasite on migratory soaring birds?

I am working on a study of the collection of ectoparasites from migratory birds in Egypt

10 June 2019 7,607 3 View

Can you help me get any research on insects that parasite on the migratory birds that includes Raptors, Buzzards, Passerine and so on?

Raptors, Passerine, Buzzards, Parasites

05 April 2018 4,429 7 View

I would like to know about use Immature insect stages in Aquaculturer?

What is the usefulness of the use of insects in food alternatives to humans and Farm animals as protein alternatives?

22 October 2017 9,633 4 View

Do heat-treated VC and heat-treated SCC have similar or distinct performances seen their early age and long term strengths and their porosities?

comparaison between heat-treated concretes (VC versus SCC): in order to make a comparison between the traditional vibrated concrete (VB) and the self-compacting concrete (SCC), made with the same...

16 March 2015 3,042 1 View

Is there a limit in loss of strength, specified by standards, that is it should not be exceeded in case of precast concrete or heat-treated concrete?

is there a limit in loss of strength, specified by standards, that it should not be exceeded in the case of precast concrete or heat-treated concrete.

28 September 2014 9,189 9 View

What is the used method to study the diet of rodents? How can estimate the quality and the quantity of plants consumed by rodents ?

Rodent, diet, estimate the quality and the quantity

01 January 1970 234 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View