How to calculate the plastic torque in circular shaft?

06 March 2019 1 2K Report

I want to calculate the plastic torque in circular shaft in fully plastic state, and I want to identified the radius of yielding and torque for shaft in elastic - plastic state.

Khaled Megahed

You could refer to http://classes.mst.edu/civeng120/lessons/torsion/theory_full/index.html

Badges
Science topic

More Mustafa Kadhim's questions See All

Why is electronic energy 0.000 for liquid crystal compounds and is invariable with temperature in Guassian 09 software?

Are there any suggestions or insights you can provide to help address this problem

06 August 2024 1,443 2 View

Dirty and clean?

Hi everyone I need a file with a dirty and clean potato image

04 August 2024 7,199 4 View

I need the datasets of Microgrid for system identification?

Hi I am working on data driven model of the microgrid, for that, i need the reliable datasets for the identification of MG data driven Model. Thanks

02 August 2024 5,748 4 View

Please, what is the memory consumption of the Matlab function quad tree decomposition procedure [S = qtdecomp(I)] with respect to the input set I?

27 July 2024 5,455 2 View

Provide a questionnaire for positive role of politics in nursing ?

I want to write article in a topic of positive role of politics in nursing, and I'm confused how can we add add questionnaire and what will be the questionnaires.

18 July 2024 10,021 3 View

How to simulate a varying three-phase load /load profile in Simulink/MATLAB?

I have a Simulink model that connected a main utility (AC-grid) with a three-phase load changing from 20kW to 100kW in 5 seconds and I don't know how to build this load in Simulink. Please your...

14 July 2024 8,892 3 View

Can we use 30%hydrogen peroxide for catalse activity? If can, then why?

The question us regarding catalase activity check of bacterial strains. I saw an article in which it was written that we can use 30%hydrogen peroxide for catalase activity but in our laboratories...

12 July 2024 8,794 2 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

How i can calculate mathematically COD concentration if i add 1gr from glucose to 1 L distilled water ?

how i can calculate mathematically COD concentration if i add 1gr from glucose to 1 L distilled water

08 July 2024 9,104 2 View

Taking a cut line through deck build in silvaco?

Hi everyone hope your all doing good. I’ve been looping my scripts and am trying to take a cut line of the conduction band energy with respect to y for each loop. Basically, I want to take a...

03 July 2024 9,134 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

In WECS : Gain values for conversion of PMSM rotor speed(rad/s) to p.u. input to wind turbine and Torque(pu) of WT to input of PMSM-Torque (Nm) ?

I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...

03 August 2024 888 1 View

Water Consumption in Plastic Recycling: Is it Higher Than for Virgin Plastics?

Hello, dear colleagues, I would like your help in finding a reference that provides an average water savings due to plastic recycling compared to the consumption of virgin materials, preferably...

29 July 2024 4,630 0 View

Is anyone aware of any Bronze Age or Neolithic pendants made of siltstone with serrated edges?

Excavation in 2007 in Northern Scotland along the East Coast revealed a domestic site containing the unbroken half (other half is missing) of a perforated circular disc measuring L 37mm x W...

27 July 2024 6,019 0 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

How Do Length of Pylon and Rotor Disk Radius Impact Angular Frequency and Torsional Stiffness in Whirl Flutter Analysis for a 2 DOF Propeller System?

Actually, I'm having trouble implementing the plot of the flutter region for the whirl prop system with 2 DOF (Influences of structural damping and propeller—pivot point distance on whirl flutter...

21 July 2024 5,047 2 View

Interpreting ATR-FTIR Spectra for Microplastics Research?

Hello everyone, I am currently pursuing a PhD in Environmental Engineering with a focus on microplastic studies. My background is in Civil Engineering, and I am relatively new to working with...

18 July 2024 7,258 3 View

How can we simulate(with FEM) the shape of Mobius strip using Abaqus Learning edition?

Aim is to simulate the shape of Mobius strip (an elastic ribbon) in simple way ( using Abaqus Learning edition). In literature, Mobius strip is modeled as Kirchhoff Rod / Cosserat plate. But, such...

15 July 2024 4,388 1 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View