How to calculate the matrix of standardized discrepancies using Amos?

More Jesus Montero-Marin's questions See All

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View

Which pH range is allowed for subcutaneous pump administration?

Hello, We are designing a protocol to determine the effect of certain compounds in the health of rats, but our problems have certain instability issues when subjected to certain pHs. We were...

19 June 2024 5,950 1 View

Is there any real advantage in co-electrolyzing CO2 and H2O in liquid phase to produce syngas versus using separated electrolysis of H2O and CO2?

Electrochemistry is a pathway to convert CO2 into valuable products such as CO. However, a potential side product in the cathode is H2. I wonder if it is possible to tune the composition of the...

12 May 2024 9,061 3 View

Is HK-2 reliable in its expression of kidney injury biomarkers?

I am trying to establish a model of hypoxia-reoxygenation in HK-2 cells in order to determine their expression of kidney injury biomarkers (e.g. KIM-1, NGAL, etc.) via qPCR. However, I am finding...

09 May 2024 9,223 0 View

Contextualiza LA ADECUADA gestion residuos solidos nivel mundial y local con formato APA 7 para un marco teorico de tesis doctoral ?

contextualiza LA ADECUADA gestion residuos solidos nivel mundial y local con formato APA 7 para un marco teorico de tesis doctoral

05 May 2024 3,257 0 View

What Are the Best Practices for Reporting Path Analysis?

Hello everyone, I am exploring path analysis to test mediation relationships within a dataset. What I have noticed upon reviewing the literature is that almost every article reports the results...

03 April 2024 5,957 3 View

¿Existen Investigaciones en torno a la Geopolítica Precolonial en Latinoamerica?

Me encuentro realizando una investigación sobre La Historia del Comercio Internacional de Colombia, En el Primer capítulo me encuentro abordando los imperios Latinoamericanos precoloniales como el...

21 March 2024 4,148 2 View

Can pulsed electric fields be used to generate heat?

Pulsed electric field is considered a "non-thermal" method for food processing that involves the application of short high-voltage pulses to create pores in cell membranes. However, since I am not...

13 March 2024 2,624 6 View

In your opinion, are room safes in hotels effective against the threat of burglary?

In some countries (e.g., Italy), there is an obligation for hotels of certain categories (4/5 stars) to equip guest rooms with safety containers/in-room safes. However, we wonder whether a prior...

16 January 2024 1,436 5 View

How can I extract ATP for concentration measurement using TCA?

I am currently trying to develop an ATP concentration measurement protocol for my human cultured cells. However, I have found little to no detailed protocol for ATP extraction using TCA...

27 November 2023 7,980 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Is it true that $\det(V(A))$ may be only $\pm 1$, depending on $n$, for the last symmetric tridiagonal matrix $A$?

One can try to generalize the Vandermonde determinant in the following direction: Let $A$ be any symmetric $n$-order square matrix. Consider its powers' diagonal elements $(A^k)_{ii}$ and...

08 August 2024 6,690 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How does one derive the standard deviation of a scale?

Dear all, I am working on analyzing data from a survey on student satisfaction. The survey contains items with a 7-point Likert response format that produce 12 scales related to different areas...

05 August 2024 2,141 4 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

Muayyad Ahmad

The Manual for AMOS version 22 is available for free in the following link. hope this help

http://www.uni-paderborn.de/fileadmin/imt/softwarelizenzen/spss/IBM_SPSS_Amos_User_Guide-22.pdf

Alexandru Agache

Do you mean the standardized residuals? You have to request them to be displyaed in the output by checking the Residuals Moments box under the View---> Analysis Propoerties -> Output tab....

Jesus Montero-Marin

Dear Muayyad and Alexandru, many thanks for your comments. I have found how to calculate the standardized residuals for the observed variables but not for the latent variables, please, do you know how to proceed? Many thanks again and best wishes!

Hi Jesus,

I am not sure what you mean - there is only a matrix of residuals calculated as differences between observed and model implied values.

Best, Alex

Dirceu da Silva

Dear Jesus,

I agree with Muayyad Ahmad. The AMOS manual is very didactic.

hope this help

Best regards

Dirceu