How to calculate Noise Margin in CNTFET based quaternary logic circuits using HSPICE ?

20 May 2022 0 4K Report

I have designed a standard quaternary inverter using CNTFET, but need to calculate its noise margin.

Badges
Science topic

Similar topics
Correction

More Ajay Rupani's questions See All

How to check the pH of E. coli culture initially? and how to change the pH of the E. coli culture?

I am working on E. coli 15597 prepared in Luria broth. Initially, the pH of LB is 7 after the inoculation of the E. coli it changes to 8.26 is it correct? can bacteria be alkaline?

15 October 2020 2,042 2 View

What are the best pipleline available for the RNA-Seq data analysis ?

What is the latest pipeline to run the RNA-Seq genomic data ?

12 October 2020 7,618 2 View

If an article is unknowingly published in a fake journal, is it considered as published or can the article be sent to some other journal to publish?

How do we handle this menace of fake journals?

14 July 2020 4,835 7 View

How do we differentiate conservation agriculture and regenerative agriculture in context of sustainable farming practice?

Sustainable farming practices appears into different names confusing the global audience which to follow and why? What makes conservation agriculture as different approach than regenerative...

30 June 2020 7,726 2 View

How to get DOI for my published article in a journal which has not given any DOI?

I want to know if Research Gate generates DOI for articles which has been published but has not been provided any DOI by the publisher?

23 May 2020 510 7 View

How many times do we have to check and report model fit measures during SEM?

I am trying to run a SEM which has four latent variables in it. Let us consider these variables as A, B, C and D. All are latent. Here A and B are independent variables, C is mediator and E is...

17 May 2020 4,091 3 View

What is the criteria to calculat e the plagarism?

What is the criteria to calculat plagarism for writing manuscript

06 April 2020 6,936 3 View

What happens if we lower the number of cycles in explicit dynamics for ansys ?

Hi I am a student pursing my final year in mechanical engineering. I am doing crash analysis of the car frame in Ansys software in explicit dynamics module. I had my analysis running for 2-3 days...

18 March 2020 3,709 3 View

Why contaminant is transporting from lower part to higher part in various column experiments? What is reason behind this?

can we transport the contaminant from the higher part to the lower part of the column?

25 December 2019 7,124 3 View

Can authentication in IoT be implemented using BlockChain techniques?

Authentication in IoT systems are vastly insecure. Mostly the problems lies on its open ended and probable untrustworthy nodes. Also, the need for a lighter authentication mechanism will always be...

09 December 2019 4,896 4 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Helix antenna coupling problem?

Dealing with a helix antenna, made with flexible material and not rigid like using a PCB board or wire. At the beginning of the helix is too close to the ground plane, causing coupling. How can I...

21 February 2021 4,453 3 View

FLIM Signal to noise ratio of a time series - can I use dark frames to measure noise?

I am doing an analysis on some FLIM data in the form of time series image stacks. I need their signal-to-noise ratio. Recording starts several picoseconds before the excitation pulse, so no sample...

08 February 2021 7,169 3 View

Grid connected inverter using virtual synchronous machine?

Hi everybody, currently, I am working on the grid-connected inverter. I want to make my grid-connected PV system a PLL-less system. I have studied some reachers are implementing a virtual...

07 February 2021 6,078 2 View

How to eliminate noise when using a sensor with instrumentation amplifier and giving it's output to Arduino?

When I am trying to implement a pressure sensor through instrumentation amplifier and then giving it's output to Arduino, I am getting garbage value due to noise, so how to eliminate it.

05 February 2021 8,598 11 View

Can't run my IPMSM drive system with DC-supply higher than 125 V. Have anyone had similar problem?

Hey, I try to run my 4 pole IPMSM with PWSVM and use a typical controller with PI-controller with a current loop and speed loop. When I run my system with DC-supply 100 V with a steady-state speed...

28 January 2021 7,354 8 View

How can I quantify background noise in a bioacoustic file?

I am using Audacity to analyse the presence of birds and frogs recorded with a SM4 recorder (Wildlife Acoustic). Background noise (rainfall, wind) is an important variable to consider that can...

28 January 2021 2,989 3 View

I am facing problem with integration of boost converter with single phase offgrid inverter?

i tested boost converter with MPPT and single phase offgrid inverter with close loop control separately. They work fine but when i connect them boost converter doesn't give the output as it did...

17 January 2021 6,428 6 View