How to find the number of packets in a queue within a device in NetSim?

In a network, I want to set the buffer size of a device and then measure the number of packets in the buffer queue. The number of packets in the queued, dequeued an dropped, I need to calculate...

12 September 2020 4,654 4 View

Apply frensel absorption in COMSOL in laser keyhole welding model ?

Hello Everyone, I want to apply fresnel absorption in my laser keyhole welding model. I have seen fresnel equations on the COMSOL websites. It's kinda different from the one I see it in the...

08 September 2020 9,943 1 View

Applying Convective heat flux in COMSOL Multiphysics in 2D axis-symmetric geometry ?

07 July 2020 10,020 5 View

Interface normal term in COMSOL during using Multipysics ?

Hello Everyone, I want to write the expression for interface normal. How can I write it? Cannot find it properly in "Equation view". Please see the attched figure. Please comment if someone...

13 June 2020 5,464 3 View

I want to know the BET surface area of nano-rod shaped ZnO nano-particles?

Anyone if you know the BET surface area of nano-rod shaped ZnO nano-particles than please comment. The nano rod-shaped ZnO nanoparticles are synthesized by chemical precipitation method. If...

25 May 2020 8,856 1 View

Heaviside funtion on delta(phils) function in COMSOL?

Hello everyone. I want to apply the Heaviside function on the delta(phils) as shown in the figure. Can I apply the step function as a Heaviside function shown in the figure?

19 May 2020 310 7 View

To define Heaviside function in COMSOL ?

Hello Everyone. This might be very easy but I cannot figure it out whats wrong. Equivalent visosity: "((mus)*(TTl)" It turns to yellow text>> unexpected unit of input. >> (mul and mus...

25 April 2020 7,482 6 View

I do not have any negative number in my square root. Still COMSOL shows the following error. Please help ?

I am stuck on this for days. Any help would be appreciated. The following error has shown: Repeated error test failures. May have reached a singularity. Time: 0.00052653794651556622 s. Merged...

13 March 2020 5,858 8 View

Can anybody share resources or codes to calculate A-weighted noise level from audio recordings of environment?

I have continuous recordings of different places in urban and natural areas from which I want to extract the A-weighted background noise level.

10 March 2020 5,648 26 View

Where can I get any good content or research papers based on animal biometric using iris pattern especially in cattles?

Where can I get any good content or research papers based on animal biometric using iris pattern especially

09 March 2020 1,208 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View