how to add layer deposition (Selective laser melting) in COMSOL?
I need to coat Ni-Al and Ni-20Cr on Ti6Al4V alloy. Could anyone suggest me the paper related to Ni-Al coating on Ti6Al4V Alloys? Please help me in the same. Thanks, Amit Chauhan Research...
03 April 2019 8,382 1 View
I have been researching recently in metals for aerospace engineering (fatigue application based) related to additive manufacturing. They are being printed with the enormous cost for a very small...
05 June 2017 7,464 2 View
I wanna perform Low cycle fatigue simulation for Low Cycle Fatigue Ti6Al4V specimen as per ASTM E606 in ANSYS. Could anyone please help me in providing the helpful tutorial/resources for the same?
04 May 2017 8,501 0 View
I want to perform strain controlled fatigue test in FEM. Could anyone help me in finding the source/tutorials or anything pertaining to that?
04 May 2017 5,939 7 View
I am manufacturing Ti6Al4V by SLS (AM) and I am interested in fatigue performance of same component pertaining to aerospace applications. Therefore, Could any one of you tell me that whether Low...
01 February 2017 5,408 3 View
Is there any tutorial in COMSOL for Selective Laser Melting?
31 December 2016 9,037 3 View
I want to perform simulation pertaining to SLM (Selective Laser Melting) in FEM and/or comsol. Could anyone please suggest some good ebooks/pdfs/tutorials for the same?
31 December 2016 2,051 0 View
How to open Comsol 5.2 version file in Comsol 5.0 or lower?
31 December 2016 9,266 4 View
I have done extensive literature survey related to SLM and all other process (including review articles, as well as latest to oldest papers as much as I could found and also with various...
11 December 2016 1,034 0 View
Is there any way to coat HA on any substrate directly by SLM? If yes, How?
11 December 2016 594 0 View
Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...
02 March 2021 4,624 4 View
How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...
02 March 2021 9,833 3 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...
26 February 2021 8,567 3 View
Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...
24 February 2021 249 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.
23 February 2021 9,086 3 View
I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...
23 February 2021 4,050 1 View
Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?
22 February 2021 2,968 1 View
How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?
22 February 2021 5,408 1 View
