How much thickness of active material we need to coat on anode and cathode current collector for a Lithium and Sodium ion batteries?

20 July 2023 1 4K Report

How much thickness and weight we can coat on anode and cathode collector for Li and Na ion Battery.

It depends on the mass loading of your electrode. After you decide on the mass loading value, try to control the thickness of the slurry during casting to get that value.

Badges
Science topic

More Kiran Donthula's questions See All

Which regression analysis will be applied if there are 7 nominal dependent variables and 1 ordinal independent variable?

which regression analysis will be applied if there are 7 nominal dependent variables(YES/NO categories) and 1 ordinal independent variable(3 categories: Low, normal, high)?

23 April 2024 9,971 3 View

How to label forest plots in RevMan 5.4?

While making forest plot Revman I label the plot as Left control and right experiment. I see that the data supports the control as the diamond is on the left. But when I change labels the...

25 February 2024 3,144 2 View

Grain size effects on antibacterial properties?

How grain size effects the antibacterial properties?

30 January 2024 6,225 1 View

Please Suggest me some techniques to Study Pollination and Breeding System of Dioecious Species in Field. Example: Baccaurea ramiflora?

Techniques Tools required Step by step Procedure

21 January 2024 8,960 0 View

How do we calculate Power handling capacity of siw based horn antenna ?

In CSt how do we calculate Power handling capacity of h plane horn antenna

12 December 2023 1,713 0 View

Suggest the method for preparation of MoS2 nanosheets?

I've tried the liquid exfoliation method but I'm not getting the results. If anyone else has tried through this method can anyone share protocols so that I can check where I'm making mistakes in...

10 September 2023 3,753 0 View

How to solve "Error in Saving Geometry Data Subscript out of range"?

Hi everyone, I have problem while saving the computed points after adding the break lines in 2d unsteady flow. here i have attached the image of the problem I'm facing.

07 September 2023 2,235 0 View

How can I decide potential window for CV and GCD analysis of electrode for supercapacitor application?

I am conducting CV analysis of a rGO-based electrode using CHI 650E workstation with platinum foil as counter electrode, an Ag/AgCl reference electrode, and 1M H2So4 electrolyte. How can I decide...

07 September 2023 5,403 4 View

Can I use negative potential window for two electrode supercapacitor?

I got negative potential window in the range of -0.6 to 0.3 for 3 electrode system ,so can I use negative voltage window for -0.6 to 0.4 for 2 electrode supercapacitor system.

03 August 2023 1,765 0 View

What is difference between sine and 5 sinewave and 16 sinewave?

while I am performing EIS in Autolab (NOVA 2.1.6) Metrohm,there are three types of options are available .what is difference between them .

27 July 2023 4,499 0 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

What is the reason for current dropping in OER , LSV curve?

I tried four trials of the same Copper Phosphides sample in Alkaline medium ( 0.5M KOH) with Hg/HgO reference electrode and Pt as counter electrode. I used 0.001 V/s scan rate for first three...

10 August 2024 3,629 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

How to find a reaction is reversible or irreversible in CV? How to know the number of electrons transfer?

My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...

30 July 2024 4,671 3 View

How to check pH of a high strength hydrogel?

We are working on biopolymeric hydrogels. Our system is highly viscous and sticky, and the gel formed are high in strength. We are unable to use pH electrode and pH strip. Please suggest an easy...

30 July 2024 942 2 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View