How to model the damaged concrete in OpenSees software For beam or for column section ?

I working to modeling of damage reinforced concrete beam ,column, beam-column joint using in OpenSees .please any example or code for To clarify this issue.

01 January 1970 8,296 1 View

How can I model a hummer impact in ansys-autodyn program?

"the model is cantilever pier of bridge a hummer impact was applied at the top of the pier to get the free vibration response" thank you very much

01 January 1970 7,186 5 View

I need an example of using element s?

01 January 1970 7,168 7 View

How can i use cohesive element in ansys to simulate czm in shear mode test?

my dears, please, how can i use cohesive element in ansys to simulate czm in shear mode test using ANSYS program? is there any article explain this problem. hala

01 January 1970 854 6 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How do you write a simplified C block code of this average-current control on PSIM?

This is a Buck (step-down) Converter and I am new to this program. I need to program with simplified C block and I actually don't know what to do. Can anyone show me how to do this? Or at least...

02 March 2021 8,233 1 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Do you know good and user-friendly programs to measure plant quantitative traits?

For my research i will need to measure plant quantitative traits (especially leaves area and roots length, but would be nice to add some more information). I recently discovered...

01 March 2021 5,035 2 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View