05 May 2017 1 3K Report

Need to interpret the trends shown in charts.

More Tarika Singh Sikarwar's questions See All
Why does the value of KMO not displayed in spss results for factor analysis?

The sample size was of three hundred respondents and the questionnaire has 45 questions.

03 April 2017 6,897 10 View

Is there a questionnaire available to measure family role and their interaction with investment goal formation?

Though a conceptual work is available but I want to know  how to carry it out empirically 

10 November 2016 5,185 2 View

How to write the research methodology of a case based method of research..the method is in depth interview?

The research I want to carry out is through open ended questionnaire..

10 November 2016 7,749 8 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close