Is IMPACT FACTOR justified in case of Taxonomy?

There is huge pressure of getting good impact factor on scholars now a days. On the other hand Taxonomy is a very dry subject and the concerned papers can only get citation in same group of organism.

26 February 2021 5,851 1 View

Why tick's salivary gland extract didn't run in the gel (SDS PAGE )??

Greetings, I want to make SDS PAGE for my sample (Tick salivery gland extract), I tried concentrations 10%, 12%. I also tried high molecular weight ladder. But the protein stopped at the top and...

25 February 2021 7,698 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

How to measure the pH of Peat Soil?

Peat possess organic content above 75% and is highly acidic in nature (i.e. pH < 4). Before commencing stabilization, it is mandatory to know about the pH level of peat. Therefore, your...

18 February 2021 9,424 7 View

How to Measure Consumer Willingness To Change from petroleum-fueled vehicle to electric vehicle?

I wanted to calculate the probability of one consumer shifting from using a petroleum-fueled vehicle to an electric vehicle. Since my background is in engineering I do not know much about how to...

15 February 2021 9,190 5 View

Having trouble mounting the sections on the slides for IHC staining, what solution should I use?

Hello everyone, I just started learning IHC staining and I have some frozen sections to practice with in a 96-well plate. I'm having trouble mounting the sections on the slide, a colleague told me...

08 February 2021 6,880 3 View

How to use Image Lab to take an image for the bands and the ladder in the same image merged together in Western Blot?

Hello everyone. I was trying to use Image Lab software to take an image of both the ladder and the samples merged together in one image to see the position of the bands according to the ladder MW,...

04 February 2021 9,996 2 View

Need a research paper for multi speaker and single microphone acoustic echo cancellation?

Hi, I am working on a problem that involves multiple smartphones/tablets. All devices are playing the same sound with synchronization difference up to +- 5ms. Now, there is an echo issue and I...

02 February 2021 5,929 3 View

Can I use the result from a pilot study to decide the minimum sample size ?

Can I use the result from a pilot study to decide the minimum sample size required to compare the means using independent sample t-test ? Or any other way that can help me to determine the...

29 January 2021 7,677 6 View

How to prepare secondary antibody from lyophilized antibody?

So I'm new to lab research and learning Western Blots these days. I ordered my secondary antibody and it arrived in a powdered form. Here is the...

27 January 2021 5,402 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How do I calculate absorption coefficient of my thin film if I dont know the thickness? Or how can I calculate the thickness of my sample?

I have done Uv-vis characterisation of my thin film and have received absorbance and transmittance data. Now I want to calculate the absorption coefficient but I dont know the thickness of my...

21 February 2021 7,148 8 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View

Can fractal dimension of thin film surfaces affects the electrons energy states?

As fractal dimension of a thin film surface implies the irregularity in the surface. Is it possible that the energy states of the electrons are also affected by the fractal dimension?

19 February 2021 5,509 3 View