How heating rate play imp.role in CVD Monolayer Crystalline TMDCS esp.in WS2 monolayer?

03 April 2020 1 8K Report

Hi All,

I would like to know about heating rate per min..Is it necessary to apply heating rate 30 to 35 degree per min?will it work to keep heating rate 20 degree per min till 900 degree and then 4 to 5 degree heating rate till 1100 degree C? Please suggest your views..

Thanks in advance..

Deepa S. Narang

Thanks a lot Nisar..

Badges
Science topic

More Deepa S. Narang's questions See All

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

Which is the best software or programming language (user friendly) for analysing data?

I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...

20 February 2021 3,950 15 View

Hi..how to isolate crude HDL (all subfractions) from human serum by size exclusion chromatography?

I would like to know about isolation of crude HDL from serum by SEC. Is it possible to perform with a serum sample volume of

19 February 2021 5,576 2 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View

Do you have any experience with transfection of EBV immortalized B cells with Lipofectamine?

I know that efficiency of transfection for primary B cells is very low with Lipofectamine. But I did not try that for EBV immortalized B cells. Do you have any experience with transfection of EBV...

05 February 2021 4,159 1 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View

Ester cleavage conditions?

Hi all, I need to cleave the ester in Ethyl 2-amino-1H-imidazole-5-carboxylate to make the carboxylic acid and retrieve the product from solution to use in downstream applications of linking to...

01 March 2021 8,766 3 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

What is the error of the Txy diagram?

Hi, I know the attached Txy diagram has an error but can't figure it out. Could you please look at the diagrams and explain it to me?

23 February 2021 4,239 1 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View