How exactly does B increase hardenability of hypo-eutectoid steels and not for hyper-eutectoid steels ?
Quite good explanation you can find here:
Screenshot attached :)
http://books.google.pl/books?id=wWVgfUK0efYC&pg=PA195&lpg=PA195&dq=Boron+hardenability+hypereutectoid+steels&source=bl&ots=RzVnw3cSg9&sig=P_FM8vS2QiVC-T4w7RtopPChE8w&hl=pl&sa=X&ei=w0N4VKrXKcPeavmwgNgD&ved=0CCkQ6AEwAQ#v=onepage&q=Boron%20hardenability%20hypereutectoid%20steels&f=false
Thanks for very informative answer!!!
Does coil break marks formed in hot rolled steel, had their origin in in yield point phenomenon / discontinuous yielding? 1) How do they depend on chemistry of steel? 2) Does grain size play any...
31 December 2014 2,078 1 View
How Glow Discharge Spectroscopy can be used to characterize surface oxide films formed in hot rolling? What are its detection limits for various elements? Can it detect low atomic weight elements...
31 December 2014 10,035 1 View
Pickling Inhibitors are widely added to pickling solutions containing either hydrochloric acid or sulfuric acid. Most of these inhibitors contain Hexamethylene tetra-amine. These inhibitors are...
10 November 2014 9,452 2 View
How does B added in steel, affects both hot rolling and cold rolling behaviour of steel ?
10 November 2014 4,575 4 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?
31 July 2024 4,835 3 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View