How does one make a 3D adaptive grid in ANSYS-FLUENT Meshing console?

Samuel Luis @Samuel_Luis

09 September 2017 0 992 Report

Typically a 3D adaptive grid for simulating the afterbody flow of a reentry capsule.

Badges
Science topic

More Samuel Luis's questions See All

Does ANSYS-Fluent solve the Fay and Riddell equations for calculating Stagnation Heat flux in Hypersonic flows over blunt bodies?

Are the equations of Fay and Riddell embedded in Fluent or do they have to be imported using a UDF?

01 February 2018 7,824 3 View

In Fluent, For a density based solver for steady flow, Is it sensible to have an option for Courant number (CFL no.)?

As usually the trend is a Courant number (CFL no) can only be used for a Transient( Unsteady) flow condition. Thank you in Advance.

01 February 2018 1,960 6 View

Can Detached Eddy Simulation (DES) be used to accurately simulate flow separation in Reentry Capsule Afterbody flows?

Typically at Hypersonic Free Stream Mach numbers and to capture the flow separation and reattachment in the afterbody flow of a re-entry capsule

09 October 2017 749 3 View

Which Solver does one use to simulate flow around a body at Mach 1 in ANSYS -FLUENT?

I am not clear whether to use a Pressure Based Solver or a Density Based Solver. Thank You in Advance

09 October 2017 2,620 18 View

How does one calculate or measure Shock Angle (beta) in ANSYS-FLUENT ?

Generally after the calculation has been run and during post processing of results in either FLUENT or CFD-POST.

08 September 2017 2,201 3 View

How does one simulate a Normal Shock in ANSYS-Fluent ?

I would like to know the boundary conditions for simulating the above .

08 September 2017 1,375 2 View

Which turbulence model is most preferred for modelling Hypersonic Afterbody flows ?

Typically Hypersonic Afterbody flows involving blunt body re-entry vehicles(spacecraft) with an angle of attack and flow separation taking place in the afterbody flow.

04 May 2017 9,878 4 View

No title

These include hypersonic re-entry flows where bow shocks or detached shocks are formed.

03 April 2017 9,240 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View