How do you model an Axial flux permanent magnet brushless dc motor in MagNet software package?

More Biren Gevaria's questions See All

How are local citations different from global citations of any research article. Which one is more effective local citation or a global citation?

I am conducting a bibliometric analysis and I am trying to understand which kind of analysis has greater impact in research field.

05 February 2023 9,640 6 View

Can someone direct me to any studies reporting on the architecture of intrinsic and extrinsic foot muscles in cercopithecoid primate (e.g. macaques)?

Specifically looking for muscle masses, PCSA values, fiber lengths, etc. of muscles acting on the toes including the hallux. I am familiar with studies reporting on these properties in apes, but...

18 June 2018 4,338 6 View

How to clean the CAD detector?

The module of the CAD detector is corona Veo. It has been idle for a long time. And it was not well maintained before idle. I have replaced the gas filters and flushed the system with a 50/50...

01 August 2024 7,805 0 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View

Is VSM measurment of NdFeB alloy powder sample require any spesific sample preparation ?

Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...

09 July 2024 1,969 0 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

Why my hysteresis loops shift a little bit to left side?

I get the hysteresis loops of FeCo HEA using the Vibrating Sample Magnetometry (VSM) to measure the coercivity. I use Quantum Design Magnetic Property Measurement System (MPMS) equipped with a...

24 June 2024 8,699 5 View

How to predict the efficiency of a very low speed Railgun Actuator/Lorentz Force Actuator?

I'm not an electrical engineer or anything related to that subject, so my apologies if I understood something incorrectly. Well, I read somewhere that the slower the railgun is, the higher its...

23 June 2024 1,082 0 View

Why my maghemite sample does not give any peak ?

I prepared a maghemite sample. It is perfectly reacted to a magnet. However, when I tried to analyze with XRD, I did not get any meaningful peak. What is the reason for that?

09 June 2024 3,260 3 View

How are rms current of diodes calculated in new coupled inductor dc/dc converter?

I want to know how peak and rms current of diodes and capacitors are calculated in terms of output current? if you know good reference with details, please share here or tell me.

04 May 2024 6,277 1 View