How do I set up a cognitive radio simulation in NetSim?

More Shubham Gupta's questions See All

What are the most reliable approaches to extract key continuous frames from a video, with complete automation?

I have an input video, of skin (from a microscope that means it is magnified such that blood capillaries are visible). The idea is to extract 15 sec of continuous frames from a video of 1 min,...

02 March 2021 2,735 2 View

Which microtomy technique do you suggest for thin and delicate root sectioning ?And, how to preserve and process the roots before sectioning?

We have thin roots of from 1 year old different species of plants. We are looking into anatomical details of the roots. What's the best method to preserve and process the roots once they are...

23 February 2021 1,898 1 View

Has anyone done Archard Wear Simulation of GFRP Composite Plate in ANSYS with ACT extension or UDF?

I'm looking to do a sliding wear (plate-on-plate) simulation of GFRP composite plates with Archard Wear Model. Any hints or example steps are appreciated.

17 February 2021 1,447 2 View

Which root in this tap root system, in the picture attached, should be used for root sectioning in order to study the root anatomical details?

There are numerous roots in this tap root system. Kindly suggest or share a research paper where I can clarify the doubts as to which root should be chosen for sectioning and for further root...

14 February 2021 1,816 3 View

Possible problem for showing 0.2 sun intensity instead of 1 sun intensity in AAA class Newport solar simulator?

We have a AAA class Newport solar simulator. We changed the Xenon Arc Lamp recently (XBO450W, Make:OSRAM) as the lifetime got over. However, the intensity is coming to be only 0.2 sun instead of 1...

14 February 2021 9,998 3 View

How can I get access of UNAfold tool?

I am searching for tools to construct molecular beacons which shall be complementary to a given sequence. I don't want to design any primers. I found that UNAfold is one such tool which I could...

02 February 2021 9,065 5 View

The peptide synthesized with CTC resin have mass more (+68 Da) than the desired mass of the synthesized peptide. What could be the reason?

I am synthesizing 7 amino acid long peptide sequence with CTC resin, 50oC coupling for 10 min. On cleavage (TFA/TIPS/Water 95:2.5:2.5) I got peptide with good yield. However, It has 68 Da more...

30 January 2021 8,483 3 View

How to Make a Pre-Emulsion of Methacrylic acid, Butyl Acrylate, and Acrylonitrile to use in emulsion polymerization ?

Any answer will be useful / Surfactants / Procedure I am using this pre-emulsion in sequential emulsion polymerization

14 January 2021 2,566 4 View

How do we calculate curvature value in ArcGIS?

Hello everyone, I am trying to prepare curvature map in ArcGIS 10.4, using spatial analyst tool. I am using 10 m CartoDem (projected in UTM 44N). I am getting very different value, curvature...

12 January 2021 504 4 View

What is the difference between Introduction, Background, Literature Review and Conclusion for writing a Thesis Report?

I've recently started writing a thesis report based on my research paper. And I'm very confused about writing the chapter of the literature review because we already discusse everything in the...

03 January 2021 6,028 8 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Sai R N

Please check on what is the base station frequency. It is 54-60 or 54-66. If it configured as 54-60 then you need to change to 54-66 for using both channels.

You can also write to [email protected] and they respond very well to tech support questions

Shubham Gupta

Ok, I resolved this. Another query output reading for incumbent 1 and 2 are same. Can you please explain this ?