How do I model a pulsatile flow through an elastic pipe using COMSOL?

03 March 2014 0 8K Report

How do I model a pulsatile flow through an elastic pipe using COMSOL? If anyone has such a COMSOL model, please contact me.

Badges
Science topic

More Nabeel P M's questions See All

Is there any specific name for 'p' value appears in research papers other than "statistical significance" or "test of significance" etc?

p < 0.05 was considered statistically significant

03 April 2016 8,472 5 View

Is there any direct solution for the equation of the form : x.Log(1 + a/x) = b ?

What is the solution for x ; such that x.Log(1 + a/x) = b ? Currently, I am calculating the value of x by substituting a range of values for x in the LHS and find the minimum deviation from...

03 April 2016 4,603 4 View

Is it possible, if possible how to express difference between two numbers as a function of their ratio?

How to express, a-b = f(a/b) ; f( ) = ? and b not equal to zero.

02 March 2016 1,921 10 View

Journals to publish Blood Pressure (BP) measurement equations?

Please suggest me few journals to publish mathematical equations and methods for non-invasive blood pressure measurement.

08 September 2015 9,407 1 View

How can I fit an exponential curve of the form y = A.exp(B.x) + C ?

I have values of dependent variable (y) and independent variable (x). x and y are exponentially related. I want to fit an exponential curve...

03 April 2015 8,709 8 View

What is an optimal software for blood flow simulation?

Which Fluid -Structure Interaction (FSI) software is best (simple, easy for analysis and requiring minimum computer hardware configuration) for the simulation of blood flow through the artery?...

31 December 2013 5,013 3 View

Any suggestions for solving this exponential equation?

Solve for B, t1, t2 A1 =B.e^pt1 A2=B.e^pt2 . t2 - t1 = c ; known constant. p also another known constant. Any method is acceptable.

11 December 2013 4,502 7 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View