How do I make void regions transparent in abaqus odb file for effective visualization of voids?

More Prashant Chauhan's questions See All

How to define surface definitions in Smooth particle dynamics modeling of friction stir welding?

I am sharing a screenshot of the problem.

03 April 2017 8,849 0 View

What can be the reason of non- convergence in Eulerian analysis?

There is no mesh deformation in eulerian analysis,still at times solution do not converge in abaqus.What can be the probable reason behind this.Please suggest...

10 November 2015 9,230 1 View

How can I rectify a convergence issue in my simulation on coupled eulerian lagrangian of friction stir welding?

The total time period of step is 5.5 sec but after 0.5 sec there are increments and changes in energy but no change in time.I have attached a snapshot showing the same.Please suggest.

10 November 2015 4,401 6 View

How can i reduce computational time for eulerian analysis in abaqus?

I want to reduce the computational time of my coupled eulerian lagrangian analysis .Since mass scaling cannot be done for eulerian bodies .What other strategy can help me reduce computational...

08 September 2015 10,005 2 View

No mesh deformation??

i am working on coupled eulerian lagrangian analysis of fsw in abaqus.Although i am getting some values of stress strain but there is no mesh deformation .Please suggest.

07 August 2015 7,364 0 View

Since mass scaling cannot be done for eulerian analysis. How can we reduce computational time in that case in ABAQUS?

I am working on coupled eulerian lagrangian formulation in abaqus.

07 August 2015 8,107 0 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Martin Baeker

You can do this in the display manager. Choose elements -> result values, choose the corect field variable and set the boundaries for min/max as appropriate (0.5 for the filling of the element is probably fine), then replace/remove the elements.

Prashant Chauhan

@Martin Baeker : if i remove elements by entering min max value of a particular field variable, i am not getting smooth contours.

O.k., then try to do a view cut, see the CAE manual

Viewing output from Eulerian analyses (28.7 in 6.12)