How do I get a results table in ANSYS using design assessment combinations?

More Pedro Barrios's questions See All

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

Should I remove an item from a scale to raise Cronbach's alpha and McDonald's omega or is it better to leave it if they are both over .7 already?

Hello! I have this scale which had 10 items initially. I had to remove items 8 and 10 because they correlated negatively with the scale, and then I removed item 9 because Cronbach's alpha and...

01 August 2024 4,606 7 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

How to Input and Analyze Results for an Asymmetrical Factorial Design in STATISTICA 13.3?

In STATISTICA 13.3, I used the Experimental Design Builder under the Design of Experiments tab to generate a design matrix for an asymmetrical factorial design (1443) with 12 experiments. However,...

29 July 2024 4,155 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View