How do I do exfoliation graphite in NMP with a low power sonic bath ?

More Tingting Yan's questions See All

What you can do for a thin and good tem-sample?

Does anyone do the reaserch about graphitic carbon materials,if you want to make a beatiful TEM image ,what you can do for a thin and good tem-sample?I want to make my sample thiner and like one...

08 September 2015 8,172 5 View

How can I make activited carbon or amphours carbon become graphite?

My sample only partially graphitized, I hope that it will fully graphitized, or some high degree of graphitization.(the Raman specturm of my sample after High-temperature annealing)

03 April 2015 4,496 5 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How to Study a proton NMR of Graphene prepared by Electrochemical Exfoliation technique?

I performed a Proton NMR of graphene powder prepared by electrochemical exfoliation technique. It shows some peaks. But I can't understand it.

21 February 2021 8,947 3 View

Which compound is getting oxidized during bulk electrolysis with TFAA?

The experiment is really simple. When I do a bulk electrolysis with 1% TFAA (ACN solution) to get dihydrogen, what is going to be oxidized? (working electrode graphit, counter electrode platinum,...

18 February 2021 4,430 1 View

Tingting Yan

Really , thank you.Let me have a try.

Can you tell me what's the “horn type glassware”?Erlenmeyer flasks,Flask or others？

I can't see your pictures ,and my email address is [email protected] or [email protected]

Hi,Linas Sébastien ,tkanks for your help , I will read that papers carefully and I will try !