Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View

Do you have some articles to recommend about comparative experimental study about gas and water flooding with oil reservoirs?

I would like to know in the oil extraction, which is more efficient: gas flooding or water flooding? Will water flooding be more efficient in hydrophilic reservoirs with capillary...

29 December 2020 3,471 3 View

What does this PZC data mean?

I measured different kinds of catalysts which were dispersed in DI water.I firstly added certain amount of HCl and then used NaOH to titrate and measure the pH value. What does this result mean?

27 December 2020 5,728 4 View

How to inhibit the ion conversion between Mn4 + and MN2 +?

Dear scientists, I have a question to ask you, it is known that Mn4+ is beneficial to the soil, but part of Mn4+ in the soil is easy to be converted to MN2 +, is there any way to inhibit its ion...

21 November 2020 1,200 5 View

Failure in using Gene Pulser Xcell (Biorad) ?

02 October 2020 8,642 1 View

Hi everyone, how can we remove the snow-covered areas in global scale?

We obtained the global results using remote sensing reanalysis dataset. But the snow-coverd areas should be removed (like the blank area in the picture below, sources: Purdy et al., 2016). Does...

20 September 2020 3,463 5 View

How to set the fluent simulation species transport density item?

I use fluent to simulate species transport. The medium is sulfur hexafluoride and air. There is a density item under the mixture, and there is also under the fluid. Is there any difference between...

29 July 2020 7,414 4 View

How to detect brown pigments generated in red wine aging process ?

During aging or storage, the concentration of monomeric anthocyanins decreases rapidly, while low level of polymeric anthocyanins generates, and the color of wine turns brick-red gradually. In...

17 July 2020 6,032 4 View

How to calculate mode overlap ratio in Comsol ?

As is shown in attachment, there is hybrid plasmonic waveguide (HPW) and dielectric waveguide (DW), I want know how to calculate mode overlap ratio to evaluated the mode distribution similarity...

14 July 2020 2,275 3 View

Is there any organic solvent for MnCO3?

Since that my experiment could not be proceeded in aqueous. Anyone who know is there any organic solvent for MnCO3, the concentration could be as low as several mg/mL. Thanks

02 July 2020 9,654 19 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Isolates of Hymenoscyphus fraxineus?

Dear Dr. Cai, my name is Simone Prospero and I work in the team of Phytopathology at the Swiss Federal Institute for Forest Snow and Landscape Research (WSL;...

01 March 2021 1,133 1 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

What is the most suitable medium of ascomycetes fungi ??

What is the most suitable medium of ascomycetes fungi ??

26 February 2021 4,413 1 View

Has anyone used the Illumina ITS1 primer sets?

Hi everyone, Illumina provides a list of primers to amplify with high taxonomic coverage the ITS1 region for further fungal sequencing, but I cannot find the exact amount necessary of each...

25 February 2021 6,969 3 View