How do I aminate GO (graphene oxide)?

More Feras M. Kafiah's questions See All

Is there any known result about the existence of positive solutions of autonomous nonlinear BVPs?

I am trying to prove the existence of positive solutions to: -y''=f(y), 0

14 December 2017 1,677 20 View

What are the factors that control the absorption capacity of water super-absorption polymer salts? like Sodium polyacrylate?

What are the factors that controlling the absorption capacity of water super-absorption polymer salts? like Sodium polyacrylate?

25 October 2015 5,728 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View

How can I calculate teh crystallinity degree of graphene oxide?

I had treat my XRD diffraction pattern by Highscore to calculate the crystallinity degree Xc and I have the formula but I dont no the 2Theta of Ac and Aa to calculate Xc. Is it like polymers...

10 February 2021 6,305 5 View

About XRD details of pristine and doped RGO?

Hi Can anyone please help me know the XRD details of reduced graphene oxide, Nitrogen doped reduced graphene oxide, Sulphur doped reduced graphene oxide, Nitrogen and Sulphur co-doped reduced...

08 February 2021 3,033 3 View

What is the difference between Graphene Oxide and Expanded Graphite?

What are the main differences between Graphene Oxide and Expanded graphite, in terms of surface functionalities, conductivity, d-spacing and other features? Is the term expanded graphite...

06 February 2021 9,810 4 View

Lukáš Richtera

Here are described some ways to introduce -NH2 groups to GO.

http://pubs.rsc.org/en/Content/ArticleLanding/2015/RA/c5ra07892j

http://www.rsc.org/suppdata/cc/c3/c3cc49529a/c3cc49529a1.pdf

http://www.sciencedirect.com/science/article/pii/S0021979713002890

U. Chinna Rajesh

The epoxide functional groups on graphene oxide can be open with the p-phenylenediamine (PD) to afford the amine functionalized GO. Please find the attached Ref.

Article Chemical amination of graphene oxides and their extraordinar...