What software would be best to simulate impact environment ?

I am trying to investigate the impact nature of steel balls (4 cm diameter) on steel plates. Which modelling software would be best to study the stress fields generated or any type of failure...

11 December 2019 1,810 4 View

What is the optimum austenization hold/soak time for cast structures?

I am looking for studies related to austenization soaking times and ways to reduce the time to achieve full dissolution of carbides as well as not to obtain austenite grain growth. Grain growth...

10 November 2019 4,647 3 View

Are there any studies regarding fully pearlitic/eutectoid steels with relation to soaking time during austenization ?

I am working on developing fully pearlitic steels with fine interlamellar spacing. I am going to heat up samples to austenization temperature (1000 degC) at a heating rate of 10 degC per second...

09 October 2019 5,192 3 View

Are there any relevant work on impact-abrasion wear testing?

I am working on a project involving studying the impact-abrasive wear during grinding. I am interested to know if there are any relevant papers that has studied or tested impact-abrasive wear of...

08 September 2019 6,836 2 View

Can MATLAB be used to simulate nano or micoindentation by Berkovich or Vickers?

Can 2 dimensional simulation of indentation be done using MATLAB? if yes, I would really appreciate guidance from experienced MATLAB users !! Thank you

10 November 2018 1,930 2 View

What can be the reason for reduction in hardness and toughness of thin films or coatings due to doping with silver (Ag) ?

I have deposited pure Cr and W films by unbalanced magnetron sputtering method and then prepared films by doping them with Ag. The hardness and modulus of these coatings are lower than that of the...

01 February 2018 4,931 10 View

Does the presence of excess lattice oxygen in thin films or coatings signify high surface energy of the films or coatings?

In cerium oxide coatings, I have found that there are excess lattice oxygen when oxygen to metal ratio is quite high. Does it mean that the coatings have higher surface energy when there is excess...

31 December 2017 4,859 3 View

Where can you purchase synthetic/artificial synovial fluid or anything that closely resembles synovial fluid?

I am designing experiments to study the tribological behaviour of coated Ti6Al4V in synovial fluid. Any help would be highly appreciated.

10 November 2017 2,373 2 View

Can anyone kindly suggest me where to start learning simulation/modelling of Nanoindentation?

I would like to learn FEA method for nanoindentation for materials. I would really glad if someone would suggest as to where I should start learning simulation/modelling.

05 June 2017 6,778 4 View

How to calculate the adhesion energy of coatings from progressive load scratch testing?

02 March 2017 5,266 0 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

1. What is the impact of having different scales in a survey? and how can we solve this problem before and after data collection (Literature)?

1. What is the impact of having different scales in a survey? and how can we solve this problem before and after data collection (Literature-based reflection)? Thank you for your time and for...

03 March 2021 2,870 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

No title

02 March 2021 3,060 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How Relativistic effects is one reason for lanthanide contraction?

The Lanthanide contraction which is the decrease in ionic radii of the elements in the lanthanide series from atomic number 57, lanthanum, to 71, lutetium, is due to poor shielding of the 4f...

01 March 2021 2,272 4 View