What are the interactions could happens in-between polyaniline and methacrylate groups ?

Most of research studies made a composite of methacrylate and polyaniline, but most of them just describes interaction is physical adhesion. But when examine the number of papers there and many...

31 December 2017 7,950 2 View

Is there any possibilities to overlap XPS peaks in nanocomposite?

03 April 2017 3,332 8 View

How to prove the in hybrid nano-composite whether individual agents attached chemically by using XPS?

I have made a nanocomposite, by adding two chemical compounds and I want to check there are some chemical bonded internally or not..so which area I should concern more?

03 April 2017 3,267 2 View

Did anyone knows how to calculate the capacitance from this type GCD curve from Red-ox supercapacitors?

01 February 2017 3,737 3 View

How to find the standard electrochemical oxidation and reduction potential and how its related to peak current positions in CV curves?

I need to find out the oxidation and reduction potential of Copper. Oxidation of Cu(0) into Cu(+1) and Cu(+2) and reduction of Cu(+2) into Cu(0) and Cu(+1) are the details that I want to find out,...

10 November 2016 7,276 6 View

How to get the correct square shape in cyclic voltagram when measuring the supercapacitor electrode?

I have prepared supercapacitor electrode. Its is Graphene Oxide coated on Ni foam. I measured it within three electrode system. Pt electrode as counter electrode and Ag/AgCl electrode as reference...

09 October 2016 2,887 16 View

For Supercapacitor applications Nickel foams as current collector in electrode. Can any one tell me about the cleaning process of these Nickel foams?

Some publications used 1 M HCl in 10 min. washing. some are saying just ethanol and acetone can only be used for the cleaning and They comment HCl will oxidise the Nickel and our CV graphs will...

09 October 2016 7,179 3 View

How to find out potential window of the CV and GCD graphs for supercapacitor measurements?

here I have used 3 electrode system, with different types of electrodes such as 6M KOH, 5M NaCl and electrodes are graphene coated Nickel Foams. Is this same potential window can be applied for...

09 October 2016 8,066 6 View

What is the meaning of percolation of thin films? and what are the related measurements of that thin film percolation?

09 October 2016 4,692 1 View

Do we able to get same data from Impedence analyser that gave from Electrochemical impedence Spectroscopy for characterize supercapacitor?

07 August 2016 339 7 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

How to calculate refractive index (n and kvalue) against energy (in eV) data for alloyed nanomaterials through Independent Phase Approximation method?

Suggest me the method or some other software to calculate the above said data for nanoparticles.

21 February 2021 3,350 7 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View

Which method is preferable for cutting the nanocomposites?

Which of the methods like water jet cutting, diamond cutting, laser cutting, etc. is more suitable to cut the carbon nanotubes reinforced epoxy composites into test sample to ensure the clean...

29 January 2021 1,354 5 View

What is the harmless way of cutting epoxy filled nanocomposite ?

I want to cut epoxy filled nanocomposite for FE-SEM analysis. What is the best way to cut it without resulting in any cracks or change in position or alignment of the particle reinforcement ? Also...

28 January 2021 7,084 5 View

How to get rid of the solvents from a PU-Ag nanocomposite?

I've synthesized a polyurethane-Ag nanocomposite and the product is dissolved in a two-component system i.e. DMF and DMSO. I wish to know of any ways that I can use to get rid of the solvents and...

27 January 2021 1,847 3 View

Will you suggest recent literature regarding photocatalytic applications of nanomaterials?

Dear esteemed researcher, Please, suggest recent literature links related to photocatalytic applications of nanomaterials. Regards, Dr. Vinaya Tari

26 January 2021 3,930 9 View

Why degradation of pesticides is maximum at specific pH by using nanoparticles and nanocomposite?

actually, I am degrading pesticides by using inorganic composites the pH of the pesticide in distilled water is neutral the pH of nanocomposite is also neutral then why maximum degradation takes...

23 January 2021 8,775 3 View