07 July 2018 1 8K Report

Our students are interested to model VFET. But how can we start with modeling of VFET? What should be the first step? What methods to follow? What simulators may be used?

More Muhibul Haque Bhuyan's questions See All
What is the prospect of getting BSc Engineering Degree by Diploma Holders?

If a person gets a 4-year Diploma in Engineering Degree then does he/she need to get 4-year BSc in Engineering Degree? Is it necessary for professional up-gradation? Is there any barrier to get a...

07 August 2018 3,289 0 View

What are the factors that determine students' satisfaction at the university level?

At the university level, there are many factors that determine the students' satisfaction level. What the researchers say about the factors that determine the satisfaction level of students? How...

07 August 2018 3,308 11 View

What is Brain Engineering?

What is Brain Engineering? What are the areas of research in Brain Engineering? How to start working with Brain Engineering Research?

07 August 2018 7,693 0 View

What is eigen value?

We find eigen values in various cases, like in electrical and electronic circuits, in control systems, in data analysis etc. Why we find it? What is the significance of eigen value? What will...

07 August 2018 7,945 7 View

What are differences between vision and strategic goals?

Sometimes, many institution makes a mistake while articulating their vision statement and strategic goal. What is your opinion? Is there any difference between these two? If it is yes then how to...

10 November 2017 1,688 5 View

Why conference papers are not counted for promotion, only journals are counted only?

Every year so many conferences are held and many researchers present their papers and these are reviewed too. But these papers are not used as a criteria for promotion. Then why a researcher...

01 February 2017 8,519 2 View

What types/categories of question should be set for the electrical engineering students?

To judge an engineering students properly, types of questions set to them for various examination like midterm or semester final examinations. But what should be the question type/ question category?

31 December 2016 5,528 4 View

Does Industry Tour help students?

Does industry tour help students to learn subject matter? How many times a student should visit industries during 4-year undergraduate engineering program?

11 December 2016 8,518 4 View

What is teaching philosophy?

University teachers need to submit teaching philosophy. Is it mandatory? Why it is required? Does it required from all levels of teachers?

11 December 2016 1,664 6 View

What factors determine the student satisfaction of engieering students?

At undergraduate level engineering students, what are the factors that will attract and sustain students to a particular program/department?

11 December 2016 8,811 5 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,113 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,003 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,891 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,047 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 717 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,984 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 452 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,664 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,027 4 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close