How can we simulate laser ablation of Au thin film on glass substrate using COMSOL ?

09 September 2015 0 6K Report

I need some guidance in setting up the heat source equation. Besides that, any information regarding how to simulate phase change in COMSOL regarding to heat transfer in solid.

Badges
Science topic

More Fang Sheng Lim's questions See All

How to calculate SERS enhancement factor (EF) with plasmonic nanoparticles on glass using Congo Red as Raman active probe ?

Based on certain articles, SERS enhancement factor can be classified into single molecule enhancement factor (SMEF), SERS substrate enhancement factor (SSEF) and analytical enhancement factor...

11 December 2017 742 1 View

What are the difference in terms of mechanical properties of metal and its respective metal oxide in nanoscale?

Specifically, Ag nanoparticles and Ag nanoparticles with an outer layer of Ag2O.

09 October 2017 3,008 1 View

How to determine the ablation threshold of Au thin film (50nm) ?

The Au thin film is deposited on a glass substrate of 0.1 mm thickness and irradiated by a nanosecond pulsed laser with wavelength of 532 nm and pulse duration of 0.9 ns. I have measured the...

02 March 2016 9,207 3 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How can I measure the thickness of thin film by Uv-Vis?

06 August 2024 7,810 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View