How can we plot grain size distribution from SEM and AFM images?

10 October 2018 0 8K Report

I have one AFM image where size of the structures are within 500 nm. How can I plot a distribution of sizes from the above?

Badges
Science topic

Similar topics
Computer Science
Images

More Basanta Kumar Parida's questions See All

Is Monte Carlo simulation a free package or any program is there to run it?

If anyone have any idea about monte-carlo simulation , please share.

03 April 2019 9,626 2 View

How can we calculate conductivity/resistivity or either from I-V curve of a thin film?

Hello, I have deposited Sputtered thin thin film of thickness 1 micron. I have measured the I-V characteristics of this, how can I measure the conductivity form these I V plots? I don't have any...

01 February 2018 1,470 0 View

How to measure hysteresis curve of cobalt thin film?

how to measure hysteresis curve of cobalt thin film?

01 February 2017 9,622 0 View

How to calculate energy deposition depth from SRIM/TRIM data?

The stopping range, lateral straggling, longitudinal straggling can be calculated from SRIM TRIM but what will be the enegry deposition depth ? In the attached pdf fig-1 . 'a' is the energy...

10 November 2016 4,976 6 View

How can we measure hysteresis loop by Magnetic Force Microscopy(MFM)?

We have cosputtered deposited thin film of Co(x)Si(1-x). I want to measure MFM study of these thin films. Anyone plz suggest how to measure hysteresis loop from MFM images.

09 October 2016 5,400 7 View

What does it mean by 'narrow range of wavenumbers present in the surface structure'?

If some regular structure are created over the surface by any of the means like ion, laser etc, what does it mean by 'narrow range of wavenumbers' ? Is it combination of waves or what?

08 September 2016 1,296 4 View

How to know the real sputtering yield of compound semiconductors from SRIM?

If GaSb or III-V type semiconductor is taken as the case and 1 keV energy Ar ion is used ,how can I calculate the sputtering yield of individual element from SRIM?

08 September 2016 5,067 2 View

How to solve anisotropic Kuramoto-Sivasinsky equation ?

If anyone knows how to solve KS equation numerically in Mathematica ,help me?

03 April 2016 5,538 7 View

What is the difference between ion beam erosion, irradiation, and etching?

I am confused with the two terms that Ion beam eroded ,irradiated surfaces and ion beam etched surface. Is there any specific difference in between these terms or have the same meaning?

02 March 2016 6,781 4 View

Does anyone have Kuramoto-Sivashinsky equation solutuion i any programmable language.?

If anyone have the numerical solution to Kuramoto-Sivashinsky equation please share with me.

01 February 2016 7,031 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to increase simulation box size?

We intend to study the interaction between peptides and polymer (like PP, PE and PS) through MD simulations using Martini force fields ( Martini 2 for PP and Martini 3 for PE, PS). We have...

08 August 2024 4,842 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View