How can we model generator using Open Modelica Software?

24 April 2020 0 4K Report

Since I am new to Open Modelica Software. Please guide me in this regard if the members has any idea regarding it.

Thanks.

Badges
Science topic

More Sonam Dorji's questions See All

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 724 3 View

How to retain amplicon yield after Ampure bead cleanup, following a 2-stage PCR protocol?

Hello all, I have been trying to follow a 2-stage PCR protocol used to amplify barcodes of a large yeast library, as per Nyugen et al. (2022) -...

30 July 2024 840 2 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 486 0 View

How Can I Resolve a Persistent Unwanted NMR Peak at 1.25 ppm?

Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...

15 July 2024 9,065 4 View

Intracerebroventricular (ICV) AAV inj.?

I'd like to know if anyone has got experience in intracerebroventricular (ICV) AAV inj. I am looking for a concomitant spread of the AAV including but not limited to the motor cortex and the...

12 July 2024 780 0 View

What are the recommended rapid response scopus indexed journals in computer science?

Kindly provide their URLs. Thank you

30 June 2024 8,475 0 View

Is anyone who knows how to buy AMOS sofware?

I have been working in Hanoi University of Public Health. I would like to know where and how I can buy AMOS software?

28 June 2024 6,591 1 View

How to form the state space model of SMIB with Power Electronic Load?

I am working on a small signal stability analysis of a power system on a power electronic load. The power electronic load is modeled as a voltage-dependent load and has the relation attached in...

26 June 2024 2,496 1 View

Cut PDMS sheet with Graphtec cutter plotter CE6000-40?

Dear All, I want to cut PDMS sheet with thickness of 0.8 mm to rectangular shape with Graphtec cutter plotter CE6000-40. What condition do you offer? Do you offer any kind of special speed or force?

25 June 2024 8,111 1 View

As the New JCR impact factor is just released. I need a list of journals which are not tracked for impact factor this year or which are delisted?

As the New JCR impact factor is just released. I need a list of journals which are not tracked for impact factor this year or which are delisted by JCR. Thanks!

24 June 2024 6,586 2 View

Visualisierung von Kugellagern in Modelica？Wie baut man Kugellager in Modelica?

Wie baut man Kugellager in Modelica? Es dient der Modellierung, Simulation und Visualisierung seines dynamischen Verhaltens. Wie soll das Verhältnis zwischen den verschiedenen Komponenten des...

23 April 2024 8,420 0 View

Is there an "air pipe model" in TRNSYS or Modelica? How reliable are the regular pipe models for air as the substance, instead of water?

Dear network, I am planning to use a model of air pipe, preferably in TRNSYS or Modelica to simulate its performance as an "air-to-ground heat exchanger". As far as I know, there should be...

18 September 2023 2,394 0 View

[Open Modelica] How do you model an AHU to find efficiency of the heat transfer of the air and water mediums in the cooling coil?

I am undergraduate student and have just started learning how to model HVAC systems using the open modelica connection editor. I have learnt through the building library examples and came across...

12 July 2023 5,835 0 View

Is there anyone who is well known with Open Modelica Simulation?

Hello everyone, I am a master's student and study energy engineering. Currently, I am working on a Heat recovery system in a simple house, and performing my simulation in Open Modelica. I want...

01 April 2023 6,274 2 View

Is it possible for Co simulations with IES-VE.?

Can I couple IES-VE with other tools like MATLab or Modelica? My research is focused on control for better thermal comfort and indoor air quality. So I want to use MATlab or Modelica, it will be...

28 April 2020 6,785 5 View

How to ensure the initialization convergence in Modelica model?

Currently, I am evaluating if I could use Modelica to build a solar power plant model. But I am facing an initialization issue. Cause the Modelica model requires good start values to ensure...

07 December 2019 9,156 5 View

Learning Dymola or Modelica?

Hi, I intend to study the application of " industrial excess heat" and "renewable energy sources" in supply of 4th generation of district heating systems. To do so, I am advised to learn...

12 October 2019 369 5 View

How i can add a PV_System library in Dymola?

I would like to create my own model of photovoltaic cell using modelica and the tool Dymola. can you help me ?

03 April 2019 179 1 View

Algorithm to reduce the size of matrix by removing all rows and columns from it which has zero value in Modelica ?

I have a matrix of size(n x n). It contains many rows and column which is filled with zero. I want to reduce this matrix in such a way that all rows and columns which has zero values is deleted....

11 December 2018 2,900 1 View

Algorithm to reduce the size of matrix by removing all rows and columns from it which has zero value in Modelica ?

I have a matrix of size(n x n). It contains many rows and column which is filled with zero. I want to reduce this matrix in such a way that all rows and columns which has zero values is deleted....

08 December 2018 2,958 1 View