Can we measure hydrogen in steel by XRD?

It is obvious that we can use XRD to measure residual stress. but I would like to know that: Is there correlation between hydrogen embrittlement with FWHM? Thank you in advance for your help.

05 June 2018 7,837 4 View

How we can measure trace elements in Alloy steel?

Ti, O, Pb, S, Al, and Ca elements in steel must be less than 50 ppm. How we can measure it in a real samples (not in the range of mg)?

09 October 2017 2,938 3 View

Polyethylene-glycol (PEG) optical properties?

Would you please tell me about light absorption of PEG? does it have light emission properties? by which mechanism?

05 June 2016 3,322 2 View

How to determine amorphous content in a mixed powder with MAUD software?

02 March 2016 6,003 7 View

Phase transition of silicon dioxide on the nanoscale?

Phase transitions are well established for bulk silicon dioxide. But I would like to now increase of the surface area and go to nano structures. These phase transitions are stable or for instance...

05 June 2015 6,231 7 View

Time temperature transformation diagram (TTT) by Thermal analysis. Would you please help me to find methodology?

I would like to obtain time temperature transformation (TTT) and / or continuous heating transformation (CHT) diagrams by Differential Scanning Calorimetry (DSC). As it clear by DSC we can...

09 October 2014 1,782 10 View

What was the previous name of NANO BIOMATERIAL in 80s?

06 July 2014 7,338 1 View

Does anyone know about the synthesis of cobinamide (vitamin B12 precursor)?

We need to synthesize cobinamide, vitamin B12 precursor. At neutral pH, cobinamide exists as aquohydroxocobinamide, and at a pH of>11, it exists as dihydroxocobinamide. From our point of view,...

04 May 2014 9,547 2 View

Reference for spectrofluorometer?

09 October 2013 6,083 0 View

Is it possible

..

09 October 2012 8,061 5 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

What should be the duration of exposure to simulated space environments with Rodents?

Hi, I am currently working on a pilot study to get some data related to the impact of long duration spaceflight to the microbiome and the immune system. I plan to use rats and simulate...

22 February 2021 592 1 View

What are effects of steel jacketing on flexural strength?

Dear all, If steel jacketing is used to retrofit a reinforced-concrete (RC) column, can we use it to improve flexural strength? I understand that we leave gaps between the ends of the jacket and...

22 February 2021 1,906 5 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How do I calculate absorption coefficient of my thin film if I dont know the thickness? Or how can I calculate the thickness of my sample?

I have done Uv-vis characterisation of my thin film and have received absorbance and transmittance data. Now I want to calculate the absorption coefficient but I dont know the thickness of my...

21 February 2021 7,148 8 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View