What will be the effective permittivity and permeability of artificial magnetic conductor?

In case of metamaterial absorbers, the effective electromagnetic parameters such as permittivity and permeability should be equal. What will these values in case of high impedance or artificial...

02 March 2018 1,497 8 View

Equivalent circuit model of dielectric?

04 May 2016 9,844 2 View

Symmetry planes in CST MW studio?

How can we effectively utilise symmetry plane settings in CST to simulate antennas on periodic surface

04 May 2016 6,407 3 View

How to simulate rcs reduction using hfss/CST mw studio?

Can anybody please help me by providing some insight to the RCS Reduction/Directivity simulation using CST MW Studio/HFSS I know RCS reduction means comparison of RCS of our structure to that of...

07 August 2015 4,443 2 View

How can i model resistive sheet in Salisbury absorber using CSTMW Studio?

how can i model resistive sheet in Salisbury absorber using CSTMW Studio?

04 May 2015 3,018 0 View

How can we derive the equations for characteristic impedance and effective dielectric constant of microstrip transmission line?

How can we derive the equations for characteristic impedance and effective dielectric constant of microstrip transmission line?

31 December 2014 3,275 5 View

Does anyone have any knowledge on high impedance surface equivalent circuits?

06 July 2014 7,205 4 View

How do I carry out a reflection phase analysis of high impedance surfaces using CST?

I want to study the reflection phase analysis of antenna for different angle of incidence. For normal incidence I got the result using transient solver in CST and using electric and magnetic...

05 June 2014 2,376 1 View

RCS reduction of MIMO antennas?

Is there any reference in literature regarding the RCS reduction of MIMO antennas?

01 January 1970 1,892 5 View

Which are the wideband dipole antennas?

Which planar dipole antennas are used for wideband application

01 January 1970 561 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

Do we need to write protocol for a second study of a systematic review that has been registered and published?

I have conducted and published a systematic review and meta-analysis research with the topic related to public health and health pomotion (protocol was registed in PROSPERO). Now we want to...

03 March 2021 8,920 3 View

How to increase a model accuracy ?

dear community, my model is based feature extraction from non stationary signals using discrete Wavelet Transform and then using statistical features then machine learning classifiers in order to...

03 March 2021 6,994 5 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View