How can simulate electrowetting process in COMSOL?

More Kourosh Vaferi's questions See All

How can find total convection heat flux in COMSOL?

When I would like to find total convection heat flux with COMSOL for a channel that fluid is flowing in it, what boundaries or domains for evaluation must be select? Must the fluid domain,...

08 September 2019 1,754 8 View

How to calculate Turbulent Kinetic Energy (k) and Turbulent Dissipation Rate (ɛ) in COMSOL?

07 August 2019 4,713 7 View

What was the first used material for made a gas turbine blade?

What was the first used material for made a gas turbine stator and rotor blades?

07 August 2019 1,848 5 View

Lift force in airfoil

When discussing the force of lift in airfoil, we say that molecules come to upper and lower sides of the airfoil must reach each other to the end of airfoil, due to the longer distance of the...

01 January 1970 2,547 6 View

Are materials with high or low thermal conductivity used in the construction of gas turbine blades?

Generally, for blades materials that have high thermal conductivity two discuss are expressing: 1- High thermal conductivity reduces turbine gas inlet energy and consequently reduces...

01 January 1970 919 9 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

Regarding LBM in Boiling?

What should be the equation for halfway bounce back boundary condition for flow field with forcing term?

08 August 2024 7,938 1 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

How to restart MD without using checkpint file in GROMACS?

Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar

29 July 2024 3,084 8 View

How to prepare a molecule for molecular dynamics calculations?

If I want to calculate molecular dynamics (Gromacs), do I first need to optimize the geometry of the molecule? For example, I first draw the molecule in Avogadro, and then what? I guess I can't...

28 July 2024 673 3 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,019 3 View