How can I to use magnitic field in ansys fluent ?

More Boumaiza Abdelaziz's questions See All

Gel electrophoresis result for total RNA samples, 1.5 Agarose gel was used, How to improve the integrity of RNA?

Gel electrophoresis, RNA degradation, RNA extraction from fresh tissue

02 March 2021 5,433 5 View

Why my Total RNA samples do not have clear two bands?

This is gel electrophoresis result for total RNA samples with good conc. However, I guess there is a problem with the purity of the samples, i can't figure out why it appears like this? And how...

22 February 2021 338 9 View

Can I make mixture of cinnamic acid with morin flavanoid ?

I am working on a project for assessing the Antibacterial activity of various chemicals, I was wondering Can i make solution of those components using water as a solvent, depending on the fact...

19 November 2020 7,857 4 View

Did anyone used microflow imaging to measure the size distribution of Multivesicular liposome which are charcterized with size (>3um)??

I have prepared Multivesicular liposomes using the following procedures: Multivesicular liposome formulations for the sustained deliv... Multivesicular liposome (MVL) sustained delivery of a...

18 November 2020 3,189 2 View

How antibodies differentiate according to match every epitope?

How antibodies differentiate according to match every epitope , ie: how takes its shape as a monoclonal

10 October 2020 9,573 2 View

I have 4 latent variables and each of which has 7 observed variables in SEM, how this affects the parsimony of the model?

I am conducting an investigation using SEM (Structural Equation Modelling) and I have 4 latent variables and each of which has 7 observed variables. How this affects the parsimony of the model?...

07 September 2020 718 3 View

How to express Nano-fluid in conservation equation of Mass, Momentum and Energy?

07 September 2020 5,903 1 View

How to examine hypothesis in SmartPLS?

Should I report the Path coefficient or Latent variable correlations after bootstrapping as the P value and T-Statistics in the latent variable correlations of two hypotheses are met while in path...

07 September 2020 6,994 2 View

I followed a common procedure to synthesize Fe3O4 nanoparticles. The problem is that XRD pattern does not show any crystal structure. Could you help?

Besides, I have performed different characterization tecniques to my Fe3O4 nanoparticles and all are similar to what is reported in literature. Those characterization techniques include FTIR, SAED...

22 July 2020 8,549 12 View

How much water does each desalination plant type produce and cost?

There are many types of water desalination plants; Reverse Osmosis, MSF, Solar desalination units, ........... etc. How much water does each desalination plant type produce and what is the...

30 May 2020 7,719 4 View

How to find the mean, SD and CI in SPSS?

Hi, I hope that someone can help me with this task: I have 5 groups of participants which are numbered in SPSS from 1 to 5 (according to their group number) and are all under the variable group....

03 March 2021 506 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Can you share me how teacher education is managed in your respective national educational system?

I feel that the practice in teacher education in my country is below the expected performance level due to very poor management system. Hope I will learn something from your experiences.

02 March 2021 1,516 4 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Aiyeki Adolor-David

Setup the Basic Fluid Flow Model

Enable Magnetohydrodynamics (MHD): Go to the `Models` tab and enable the MHD model. This option allows you to consider the interaction of magnetic fields with the fluid flow.

Define Magnetic Field Properties: Under the MHD model settings, specify the magnetic field properties.

Specify Electrical Conductivity: For MHD simulations, the electrical conductivity of the fluid is crucial. Define the electrical conductivity of the fluid in the material properties section.

Set up Additional Equations (if necessary)

Boundary Conditions

Meshing

Solving and Post-Processing

Validation

Iterate and Optimize

Garbe Chukulu

There is an Ansys Maxwell electromagnetic simulation. You can use this software, which should be installed and coupled with Ansys.

Boumaiza Abdelaziz

Garbe Chukulu , thank you for reply , can you help me , how do I use this ?

Aiyeki Adolor-David thank you for answer , but I don't have MHD model in fluent ansys , how do I enter it ?