I want to model temperature distribution in additive manufacturing, but do not know how simulate adding new layers to the first layer.
you can use NX Simulation software.
Thanks Sunil, Do you have any similar experience?
I would like to create a small guide containing the meanings of the names .. Thanks to everyone who cooperates with me in achieving it.
03 March 2021 5,266 4 View
I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...
03 March 2021 4,116 4 View
Preference in terms of the scientific aspect
28 February 2021 796 2 View
I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...
27 February 2021 1,233 1 View
It is said that fixed point theory has lot of applications not in the field of mathematics only but also in various areas. So I am looking for applications in Chemistry only..
26 February 2021 3,533 1 View
I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...
26 February 2021 8,183 3 View
While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...
25 February 2021 4,591 5 View
i have frequencies of bridge that are effected by mass of vehicle. the problem is when any vehicle pass the bridge it would add the its mass to the bridge mass ultimately mass of the bridge will...
22 February 2021 10,004 3 View
18 February 2021 6,665 6 View
Hello, I have a question. there is a circular thin foil which vibrates in vacuum, the foil restricted and moves up and down. it is like a diaphragm between two pipes . both sides are in vacuum but...
18 February 2021 8,075 3 View
Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...
02 March 2021 4,624 4 View
How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...
02 March 2021 9,833 3 View
Which tools can be used to generate machine codes for additive manufacturing?
02 March 2021 7,220 2 View
I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...
28 February 2021 8,626 3 View
I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...
26 February 2021 8,567 3 View
Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...
24 February 2021 249 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.
23 February 2021 9,086 3 View
I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...
23 February 2021 4,050 1 View
Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?
22 February 2021 2,968 1 View