How can I set up a co-simulation between ansys fluent and matlab or fluent and openfoam?

Arman Burkitbayev @Arman-Burkitbayev

20 September 2022 0 7K Report

I found one way, which is Ansys aaS. However, I do not know whether it works simultaneously or not.

can it be done through API? if yes then how?

Badges
Science topic

Similar topics
Correction

More Arman Burkitbayev's questions See All

How to clone pcDNA vector in SH-SY5Y cell line?

Dear all, How I can clone two genes in pcDNA vector, simultaneously (one of them is target gene with 500 bp length and one of them is GFP). Also, how we can transfect the vector into SH-SY5Y cell...

12 November 2020 6,122 3 View

I am looking for a text book on quantum theory which is suitable for mathematicians. Does anyone have a suggestion (instead of B C Hall's one)?

I mean a book which is written in math texts style. I saw Hall's book but I am looking for a book whuch has more details.

30 October 2020 1,636 6 View

How to simulate MSE walls for dynamic FE analyses?

Hi colleagues, Because of the complexity of modelling geogrid layers and their interfaces which can cause convergence problem in FE analyses, I have seen in practice they model the whole MSE wall...

14 August 2020 4,649 3 View

How I can see contact stress in my analysis result in abaqus ?

I want to report contact stress in my result, is that cpress (contact pressure) ? what is the different between contact stress and contact pressure? !

27 July 2020 3,767 3 View

Is it possible to simulate tip-sample interaction during Scanning Probe Microscopy in Abaqus? and if not which software do you recommend?

I want to simulate this interaction in Abaqus but I heard it may be possible only in Comsol, considering the samples are measured in Nano scale, thanks

01 April 2020 8,313 3 View

Does industrial scale Hydrometallurgical purification of Silicon exist?

There are several papers describing different hydro-metallurgical purification routes of Metallurgical Si to Solar Si through alloying, doping, nano sized grinding,... and finally leaching in...

28 March 2020 2,201 3 View

Why TiO2 powder earnd from sulfate process turns yellow after anealing?

Tio2 powder is earned after sulfate process by solving illmanite in the sulfuric acid and a purity of up 95% of TiO2 is gained . why the color of Tio2 turns yellow after 2h annealing in 900 oC...

07 February 2020 5,769 3 View

How to fine grind material in a narrow band particle size distribution?

Does anybody have ideas to mill Silica powder to micron size particles to a narrow particle size distribution (PSD)? For example grinding with planetary ball mill makes a wide PSD which is not...

19 December 2019 5,431 2 View

Hi all, could you please recommend a good review paper on the scheduling of renewable energy resources (RESs) in microgrids?

I would be very thankful if anyone could recommend some good review papers about the scheduling or economic dispatch of RESs in the microgrids. The assessment of the greenhouse gasses in the...

05 December 2019 6,335 3 View

Diffused dye front on SDS-PAGE, any suggestions on what the problem might be?

I ran these 15% gels for 90 minutes under 200 volts ( gel ran too slow), ladder looked very condense on the top and the dye front was somehow diffused at the bottom of the gel. I am sure about the...

16 April 2019 6,092 5 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

How can Gamma Ray API units be converted to CPS (counts per second)?

Oil and gas companies run gamma ray tool and take readings in API units while Gamma ray is also noted in cps, so how these units can be converted into each other?

24 February 2021 7,545 2 View

How to extract the y+ value from fluent ?

I am doing a 3D steady simulation of a wind rotor using Ansys Fluent. In order to have a y+ of 1, I created 10 inflation layers using total layer thickness method, and I started a first...

23 February 2021 2,819 3 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

How do I add a udf to Ansys fluent and does it need to be compiled before hand ?

I have a Define_CG_Motion udf written in c where do I add it to my Ansys fluent project and does it need to be compiled before that?

21 February 2021 9,347 3 View