i want to use tio2-metal complexes for degradation of organic pollutants
One can not suggest the generalise the method for doping processes . It depends on over all properties of reactants.
How much pressure?? and How much less width need?? The coating width is 0.7 to 0.9 mm
10 September 2023 2,451 3 View
Pre-sodiation and Sodiation
10 September 2023 9,313 0 View
I am trying the chemical treatment of 3D printed transparent PLA parts by chemical method (solvent dipping) using different solvents. However, a white layer is formed after the chemical treatment...
29 August 2023 8,820 2 View
I want to dilute the conc. of chloroform for the chemical treatment of 3D-printed PLA.
26 August 2023 9,896 2 View
I have fabricated a transparent composite and want to calculate its refractive index for UV light.
30 April 2023 8,567 2 View
the bearing capacity from hardening soil method and mohr-columb method is higher than theoretical method of Meyerhoff and Hansen method
30 May 2021 6,388 6 View
I am working with La(PrCp)3 Precursor in my Lab. I am not getting enough thickness after oxide layer deposition with ALD. To solve this issue I want to know about the precursor's chemical...
16 February 2020 5,913 3 View
In rapid thermal annealing usually we use Nitrogen, but in some articles I found Oxygen or Hydrogen is also used which gives better results. So which one is better among these three and what is...
21 November 2019 10,012 2 View
It has been noted that agribusiness firms are evolving in providing their own extension service in Fiji. Providing own agribusiness means an increase in costs therefore what are the motives of...
08 April 2019 8,469 5 View
i have prepared lanthanide metal complexes and i have to go through its thermal analysis,how we calculate the theoretical mass loss and compare with experimental mass loss . i had used metal...
31 March 2019 5,063 4 View
Approximate concentrations are require in compared with the WHO permissible limts
11 August 2024 2,723 1 View
Hey there, As a synthetic chemist delving into theoretical calculations for my imidazolium-based organic molecules, I would greatly appreciate any guidance on the appropriate input instructions...
09 August 2024 5,444 7 View
Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.
07 August 2024 8,782 3 View
I used humic acid at 0.044 g/kg soil in my pot experiment. But finally, I have to recommend kg/ha. Each pot's soil weight was 11 kg. What is the solution?
02 August 2024 7,186 6 View
Hello,, The metal complex ligand appears incomplete in the screen of the discovery studio visualizer
30 July 2024 3,354 1 View
Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...
30 July 2024 435 3 View
Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...
30 July 2024 7,062 1 View
Hello Everyone! I am trying to create a metal hydride system where I am trying to create a temperature control with the emphasis on measuring the concentration of the hydrogen with the hydrogen...
29 July 2024 7,577 2 View
Understand how to utilize biosynthesis to develop natural and sustainable solutions to address heavy metal pollution and improve environmental and agricultural conditions.
26 July 2024 1,469 1 View
I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose
25 July 2024 438 3 View