How can I model a post tension TENDONs ?

08 August 2016 0 9K Report

I am trying to model a post tension slab and i am facing a problem in defining the cables and the contact condition .. the system is unbonded system

help please

Badges
Science topic

Similar topics
Philosophy Of Science
Models

More Ali Jahami's questions See All

Solving a 3 degrees of freedom dynamic analysis using Matlab?

I am studying a three stories frame under a seismic load due to ground acceleration. the frame has three degrees of freedom, so the solution of the equation of motion must have 3x1 matrix. Knowing...

10 November 2018 4,373 0 View

How to mesh a post-tensioned slab with inclined tendon in Abaqus?

I am modelling a post-tensioned slab in abaqus. And I am facing a problem regarding meshing procedure. since the job is not completed due to conversion errors. the attached picture shows the...

09 October 2018 9,294 3 View

I need the ACI 562 code of repair please ?

Does anyone have the ACI 562 for repairing concrete structures? thanks in advance ..

31 December 2017 9,361 3 View

How to mesh a solid part with inclined hole in abaqus?

i am modeling a post tension slab and it has a tendon profile. as seen in the attached picture ,what is the best method to mesh this solid region? and references or vedios? thanks

10 November 2017 1,351 2 View

How to define a connector element to represent the bond-slip relations between linear element (rebar) and solid element (concrete) in ABAQUS?

I am modeling a simply supported post tension slab subjected to impact load . The slab was modeled as a solid element whereas the tendons were represented as a linear elements (wires), knowing...

08 September 2017 5,056 0 View

ABAQUS ERROR !! The maximum ratio of deformation speed to wave speed error !??

I am modeling an Reinforced concrete slab exposed to a drop weight . the units I am using are (meter , second, Kilograms and newton ). the drop weight was modeled as a rigid body with a mas of...

07 August 2017 780 0 View

How can I define the losses in my post tension system in abaqus ?

I am modeling a post tension slab using abaqus . but I need to know if there is a method to define the different type of losses in order to reach the most accurate result in my research

02 March 2017 3,227 2 View

Modeling bond between concrete and reinforcement ?

I am modeling a post tension slab on abaqus and i want to define the bond between the concrete and the tendon using the method of cohesive element .. but I don't know what are the values of the...

02 March 2017 1,536 6 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

"A Markov-like Model for Patient Progression"?

A Markov-like Model for Patient Progression" Markov Chain Monte Carlo (MCMC) Markov Chain Monte Carlo (MCMC) is a powerful computational technique used to draw samples from a probability...

05 August 2024 10,079 0 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

Why can't academics earn the money they deserve?

Only Journals make money from the articles we have worked on for years. Academics do not earn money from their refereeing. Then shouldn't the solution be a system in which academics can earn...

01 August 2024 6,469 6 View

Posthoc test lettering in JAMOVI?

Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...

31 July 2024 3,333 4 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View