Solving a 3 degrees of freedom dynamic analysis using Matlab?

I am studying a three stories frame under a seismic load due to ground acceleration. the frame has three degrees of freedom, so the solution of the equation of motion must have 3x1 matrix. Knowing...

10 November 2018 4,253 0 View

How to mesh a post-tensioned slab with inclined tendon in Abaqus?

I am modelling a post-tensioned slab in abaqus. And I am facing a problem regarding meshing procedure. since the job is not completed due to conversion errors. the attached picture shows the...

09 October 2018 9,133 3 View

I need the ACI 562 code of repair please ?

Does anyone have the ACI 562 for repairing concrete structures? thanks in advance ..

31 December 2017 9,229 3 View

How to mesh a solid part with inclined hole in abaqus?

i am modeling a post tension slab and it has a tendon profile. as seen in the attached picture ,what is the best method to mesh this solid region? and references or vedios? thanks

10 November 2017 1,111 2 View

How to define a connector element to represent the bond-slip relations between linear element (rebar) and solid element (concrete) in ABAQUS?

I am modeling a simply supported post tension slab subjected to impact load . The slab was modeled as a solid element whereas the tendons were represented as a linear elements (wires), knowing...

08 September 2017 4,870 0 View

How can I define the losses in my post tension system in abaqus ?

02 March 2017 3,124 2 View

Modeling bond between concrete and reinforcement ?

I am modeling a post tension slab on abaqus and i want to define the bond between the concrete and the tendon using the method of cohesive element .. but I don't know what are the values of the...

02 March 2017 1,405 6 View

How can I model a post tension TENDONs ?

I am trying to model a post tension slab and i am facing a problem in defining the cables and the contact condition .. the system is unbonded system help please

07 August 2016 8,596 0 View

Dear all, I was wondering if anyone knows whether MGLtools and Autodock can run on Mac OS?

I have tried to download the 64-bit version of MGLtools however, as many times as I have downloaded and uninstall the programs, an error arises that the app needs to be updated. Thank you.

03 March 2021 5,997 2 View

I got 02 moderator values defining Johnson-Neyman significance regions. Is it an error?

Hi everyone, I am conducting research for my Master's thesis. I am using PROCESS by Johnson-Neyman to analyze my Moderator model. I test the relationship between Public Service Motivation and...

03 March 2021 2,350 2 View

Do I need to do linear regression before running mediation analysis using PROCESS MACRO by Hayes ?

I just wanted to check if I need to run a linear regression separately if I am using PROCESS MACRO to run mediation analysis. Thank you.

02 March 2021 4,359 3 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

OpenBCI eeg--has anyone used them?

I'm looking to try out an off-the-shelf EEG set for some exploratory work. Curious if anyone has used the OpenBCI, and how much set-up work is required. I've heard they are more difficult to get...

01 March 2021 4,128 3 View