i am modeling a post tension slab and it has a tendon profile. as seen in the attached picture ,what is the best method to mesh this solid region? and references or vedios?
thanks
Yuo just need to make one cut to mesh it with HEX elements and than just mesh it with default settings ( you can change the Global Seed Size)
thank you very much sir
I am studying a three stories frame under a seismic load due to ground acceleration. the frame has three degrees of freedom, so the solution of the equation of motion must have 3x1 matrix. Knowing...
10 November 2018 4,373 0 View
I am modelling a post-tensioned slab in abaqus. And I am facing a problem regarding meshing procedure. since the job is not completed due to conversion errors. the attached picture shows the...
09 October 2018 9,294 3 View
Does anyone have the ACI 562 for repairing concrete structures? thanks in advance ..
31 December 2017 9,361 3 View
I am modeling a simply supported post tension slab subjected to impact load . The slab was modeled as a solid element whereas the tendons were represented as a linear elements (wires), knowing...
08 September 2017 5,056 0 View
I am modeling an Reinforced concrete slab exposed to a drop weight . the units I am using are (meter , second, Kilograms and newton ). the drop weight was modeled as a rigid body with a mas of...
07 August 2017 780 0 View
I am modeling a post tension slab using abaqus . but I need to know if there is a method to define the different type of losses in order to reach the most accurate result in my research
02 March 2017 3,227 2 View
I am modeling a post tension slab on abaqus and i want to define the bond between the concrete and the tendon using the method of cohesive element .. but I don't know what are the values of the...
02 March 2017 1,536 6 View
I am trying to model a post tension slab and i am facing a problem in defining the cables and the contact condition .. the system is unbonded system help please
07 August 2016 8,703 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View