Reference about advanced Li-Ion batteries production technologies (and methods)... ?

Dear researchers, I'm studying about manufacturing of Advanced Li-Ion batteries . I'd like have some information about technologies and methods for the production of the battery and its...

30 October 2020 1,009 2 View

Fuel Cell modeling in Aspen Plus and Aspen Custom Modeler?

Hello, I modeled a case in Aspen Custom Modeler at two modes (isotherm and non-isotherm) successfully. I exported them to Aspen Plus, but the non-isotherm case diverges and mass balance error...

22 December 2019 2,460 4 View

Which kind of Battery Model is very usefull in Simulink a Battery equalizer Circuits?

I Want to Simulink some topologies of Battery Equalizer Circuits in Orcad Capture & MATLAB simulink so I need to use a good Circuit model for Lithium Ion Batteries. I have different data...

08 November 2018 1,270 3 View

Simulation of circulating fluidized bed with comsol 5.3?

I tried to simulate a circulating fluidized bed using comsol multiphysics 5.3 based on attached PDF, but i received this error : Nonlinear solver did not converge. Maximum number of segregated...

19 October 2018 2,190 3 View

I'm going to link the aptamer and the quantum dot graphene by linking the Pi-Pi stacking?

I'm going to link the aptamer and the quantum dot graphene by linking the Pi-Pi stacking. But I do not know how much of a volume fraction, at what temperature, how long will I be in the Shaker....

09 November 2017 3,592 1 View

Which countries in ASIA implemented water intensive commodities import policy in their trade strategies (virtual water policy) ?

08 September 2016 4,636 4 View

How can I define RHS in UEL for a static analysis?

Hi every one! I'm working on developing a shell element to be implemented in ABAQUS through UEL. It's going through a static analysis. and as you may know for static analysis, ABAQUS just needs...

02 September 2015 7,641 9 View

How can I print out the global stiffness matrix in ABAQUS?

Hi everyone, I'm using UEL in ABAQUS. My model just have one 4-node beam element (defined in UEL) fixed in one end.When I'm running the UEL, it's working without any problem. But when I'm trying...

25 February 2015 8,975 3 View

Distribution of nanoparticles inside a binary polymer blend?

05 January 2015 6,019 6 View

How can I find the names of genes by accession number and sequence ID obtained through ncbi?

I want to report the name of the gene for loci that have been obtained through blast ncbi.

25 May 2014 8,049 8 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View