How can I insert the damping coefficient B and structural damping C in the ABAQUS software for Euler-Bernoulli beam modeling?

Mohammadreza Sajjadi @Mohammadreza-Sajjadi

29 April 2016 1 2K Report

David Restrepo

You can define this in the material properties.

Badges
Science topic

More Mohammadreza Sajjadi's questions See All

How to use evolutionary algorithms with real parameters in ryu sdn controller with large scale?

Hi, I wanna to implement evolutionary algorithms in ryu sdn controller in mininet, i have some challenges, how i can run the big scale topo with one sdn contoller??? and another question is to...

21 July 2024 246 2 View

How to calculate the apparent viscosity in porous media(the flow that has shear and elongation flow)?

According to the "chauveteau 1981" article, the apparent viscosity decreases at low shear rate and then increases after a critical shear rate. He didn't mention how to calculate the apparent...

16 April 2024 4,861 4 View

How much is the lift coefficients for the shear gradient force and the wall interaction force of NACA0030?

I need lift coefficients of NACA 0030 for simulate DLD microfluidic behavior in cell separation.

10 March 2024 9,796 0 View

How to make the pressure dimensionless when the Re number is changing?

Hello everyone I'm simulating some problem (fluid flow in a wavy channel) with increasing the Re number and i want to check pressure difference in it. I need the pressure difference to be...

04 March 2024 2,824 4 View

What percentage of error is acceptable for two graphs to be in-phase?

I have two graphs of pressure and velocity at a point over the time and they need to be in-phase . There is a small value of phase difference between these graphs. What percentage of this value is...

18 December 2023 3,427 4 View

Why doesn't the velocity fluctuate in a 2D wavy channel in high mesh number but it does in low mesh number?

hello everyone. i'm working on a fluid flow into a wavy channel and i wrote a time-varying equation code of pressure for inlet boundary condition of pressure in openfoam and set the...

05 December 2023 9,107 2 View

What boundary condition should i set for inlet and outlet of velocity to determine it based on pressure gradient?

Hello everyone. I'm working on a 2D wavy channel and simulating a fluid flow. I wrote a time_varying pressure equation code at the inlet boundary condition of P file in openfoam and set the zero...

27 November 2023 2,158 3 View

How and in what way do the different compounds formed in the intestine go to the brain?

some metabolic products that produced by probiotics such as SCFA and acetolactic how go and effects on brain function.

17 November 2023 4,992 3 View

How can I define a Hinge Joint (like Pin) for 2 separated discrete rigid shell surfaces in abaqus?

Dear Friends, I have a big problem defining a Hinge or (pin) joint between 2 separated discrete rigid which are both shell surfaces and one of them should be assembled with the rest single...

02 November 2023 8,055 2 View

How can I simulate DLD microfluidics in comsol?

How can I simulate laminar flow and particle tracing for DLD microfluidics in Comsol multiphysics?

16 October 2023 4,299 1 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Can diamond be grown using molecular beam epitaxy?

22 July 2024 9,755 2 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View