How can I implement stainless steel AISI 302/304 behavior in ansys workbench ?

More Abdelkader Benyoucef's questions See All

Psychological characteristics of a "novice swimming child" 5 years ?

What are the cognitive characteristics of a 5-year-old "novice swimming child", and everything related to motor learning, psychological and kinetic tests and measurements compatible with the study?

06 September 2020 9,327 2 View

Psychological characteristics of a "novice swimming child" 5 years ?

What are the cognitive characteristics of a "novice swimming child" 5 years old, all related to motor learning, psychological and kinetic tests and measurements that are compatible with the study

06 September 2020 258 2 View

What is your knowledge about the curriculum of excellence, and what are its features? Is it applied in your country?

What is your knowledge about the curriculum of excellence, and what are its features? Is it applied in your country? Your participation is great and appreciated

01 July 2020 2,103 16 View

Is MDPI still a predatory publisher?

MDPI was a predatory publisher, but some colleague told me that it was retrieved from predatory list. Is this correct?

01 July 2020 9,785 62 View

What are the skills of the twenty-first century to be available to students at different levels of education?

What are the skills of the twenty-first century to be available to students at different levels of education? Your participation is of great importance to me

25 June 2020 705 29 View

What is the effect of parental treatment during the ban on the child's personality?

Do you think that parental treatment during the ban period will affect an active role in the formation of the child's personality in psychological, social and personal terms?

16 May 2020 3,741 4 View

Can a survey question measure more than one variable?

Hello.. Example of my question is the following statement in a survey: "I encourage my friends to buy this brand" In the analysis stage, can I define this statement to represent (measure) more...

04 March 2020 6,279 5 View

In case of falling rain in some day during solar drying experiment by Indirect solar dryer integrated with PCM storage unit, can I shut down ??

In case of falling rain in some day during solar drying experiment by Indirect solar dryer integrated with PCM storage unit, can I shut down the dryer and continue next day? then how can I...

26 August 2019 5,065 8 View

How is the impact factor of a scientific journal calculated?

18 August 2019 2,371 8 View

How to separate top cell from bottom cell in a tandem solar sell to do single cell simulation in Silvaco Atlas?

I have the example 12 of silvaco atlas in wich there is a tandem solar cell. I am asking how to separate top cell from bottom cell to get single cell simulation. I tried to cut the top/bottom cell...

27 July 2019 1,337 8 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Yogi Firmansyah

As per my knowledge, you can maket it self wuth input mechanical properties of steel AISI 302/304 in engineering data.

Abdelkader Benyoucef

Thank you dear @Yogi Firmansyah for your replay, it is the only solution but i have problem how can i calculate tagent mudulus for the case of bilinear kinematic hardening behavior (is it Et= ((Su-Sy)/(eu-ei)) ? ) if i have this input http://www.matweb.com/search/datasheet_print.aspx?matguid=abc4415b0f8b490387e3c922237098da&src=xls