How can I get the ICEBOX (Orkustofnun) software?

M. Yusuf Hakim Widianto @M-Yusuf-Widianto

14 January 2014 1 4K Report

I need some program to tracer inversion (TRINV) and forward modeling (TRCOOL program) as well as the handbook to use this program.

Zhonghe Pang

I suggest that you contact the United Nations University Geothermal Training Program in Iceland for help. Good luck!

Badges
Science topic

Similar topics
Social Psychology
Attitude

More M. Yusuf Hakim Widianto's questions See All

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

How can I measure arsenic concentration in a patient blood?

I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.

23 July 2024 3,654 2 View

It is possible to conduct a structured written interview for a qualitative study?

In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...

11 July 2024 4,163 4 View

Can honey bee village be one of a solution for conservation and sustainable commercial honey production to meet future demand ?

We be glad to get someone who has experience

09 July 2024 4,759 2 View

What is Differential-Fed in microstrip patch ant? How it is design in CST studio? What is process and procedure to do Differential-Fed in CST studio?

What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?

08 July 2024 7,464 1 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

What is co-polarization and cross polarization? How can plot it from CST studio?

what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?

08 July 2024 7,869 1 View

Why in some degradation experiment the results doesn't fit first or second order kinetics ?

In an antibiotic degradation experiment using metals carbon composites to activate PMS, the results doesn't fit pseudo first or second order kinetics however the degradation efficiency is very...

26 June 2024 6,941 3 View

Why carrier Concentration decreases while increasing Temperature ?

Hi All . Recently, I conducted Hall measurement experiments at high temperatures on highly p-doped diamond with a doping concentration of 2.5×10^20 cm−3 During these experiments, I observed two...

23 June 2024 4,763 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to develop investments in renewable energy sources?

08 August 2024 5,112 3 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View