How can I get a plot of stress vs time from Ansys Workbench Autodyn?

21 October 2015 1 2K Report

I am simulating the bullet impact on Silicon carbide backed by steel material in AUTODYN. The bullet velocity is 800m/s. how can I get the plot of stress vs time and strain vs time from the output of Autodyn?

I am searching in History option in Autodyn but there is no option available for stress and strain.

if any one know the solution please share it I will be thankful

Rachayya Rudramuni Arakerimath

Dear researcher

I think you may go for Impact analysis and time history plot.

Badges
Science topic

More Numan Khan's questions See All

Why is electronic energy 0.000 for liquid crystal compounds and is invariable with temperature in Guassian 09 software?

Are there any suggestions or insights you can provide to help address this problem

06 August 2024 1,443 2 View

What is fitofthora instance of potatoes?

Now research fellow used it to prevent fungus in potato,may be potatoes gene effect.

02 August 2024 180 3 View

What is gangrine? Is there gangrine happened indie potato?

Please discuss someone told about fungus and allied others.

31 July 2024 3,372 3 View

How gold procurement?

Please note it

29 July 2024 4,920 3 View

How gold procurement?

https://www.cleanteqwater.com/resources/case-studies/gold-mine-australia/

29 July 2024 5,161 1 View

Why not cow dung manure used in lie for artificial ?

Cow dung manure is more powerful than artificial fertilizer.

19 July 2024 7,392 7 View

Why not we are following sars COVID 19 guidance?

If the case of Irak is of December 2020 then i think I can suggest pl follow all the infection cause and death, already in our researchgate.

19 July 2024 3,356 2 View

Is cow dung can be in used for repeated use ?

Is this organic cow dung manure now important than artificial fertilizer.if good then why ?

19 July 2024 9,052 2 View

Provide a questionnaire for positive role of politics in nursing ?

I want to write article in a topic of positive role of politics in nursing, and I'm confused how can we add add questionnaire and what will be the questionnaires.

18 July 2024 10,021 3 View

Is there any new COVID infected?

I have come to know one actor told publicly and media that was unable to attend marriage ceremony due to i was admitted in hospital of Mumbai.now negative so I am appeared again in front of...

17 July 2024 2,964 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View