How can i fix a problem AMOS-SEM analysis that the loading factors did not display on the arrow after the analysis is completed?

More Mamaru Dessalegn's questions See All

Molecular docking using AutoDock Vina?

I tried protein-ligand (small molecule) docking using AutoDock Vina. Before docking my compound of interest, I tried to validate the docking procedure using a known crystal structure from the PDB....

22 February 2022 7,172 2 View

Molecular Docking using PyRx software?

I am practicing Molecular Docking using PyRx software. I tried to confirm whether my docking is appropriate or not by using available crystal structure of a CDK2-dinaciclib (enzyme-inhibitor...

01 February 2022 6,497 3 View

Why techno-economic feasibility analysis is done on Diesel Vs PV energy resource in Africa especially countries proxy to equator?

I have seen a day to day phenomenon in my country, Ethiopia wherein all governmental agencies and universities are using diesel Generator sets as a backup for frequent power interruptions. So, I...

06 May 2021 3,412 5 View

Which of the following two startegies is more likely to be successful in the fight againsts superbugs?

Superbugs are major public health concern and we have different strategies to address the issue. However we need to prioritize them. which one is more likely to be successful? 1)Targeting the...

13 September 2017 4,157 3 View

Sample size, study design and data analysis

If the population of interest are few (eg 50 subjects), will it be appropriate to use cross sectional study design? What kinds of statistics are more strong in such sample size to make group...

04 August 2017 7,320 6 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Weak DAPI staining after immunohistochemistry - how to improve?

After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...

05 August 2024 9,637 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Imran Anwar

@Mamaru You should attach the screenshot of your AMOS screen after you've run model then only others can get know what's exactly happening in your case.

Zhenwei Dai

Mamaru Dessalegn It can be caused by many reasons, I suggest you attach the screenshot of your AMOS after running analysis so that we can find the exact problems.

Muhammad Anwar

Perhaps you have not selected the options needed for factor loading in the output.