How can I find the combustion model for DME air in ansys fluent?

06 August 2015 1 8K Report

If you are using non-premixed PDF method, you can create an empirical fuel by inputting percentage of the components of the fuel. You also need to input the LHV and specific heat of the fuel and then create a PDF table.

Badges
Science topic

More Ramasamy Devarajan's questions See All

How to classify Per- and Polyfluorinated Substances (PFAS) based on their toxicity ?

The contaminants known as per- and polyfluorinated substances (PFAS) are present in medical equipment and pharmaceutical products. How the toxicity profile should be categorized.

30 December 2023 6,160 0 View

How to rectify the issue 'Missing or bad data: Atomic Orbital energies line number 872' in dft (gauss View 5.0.8)?

The optimized structure of my compound is generated in .log format but for the .chk format it shows the error as mentioned in question. With the .log format of optimized file I submitted the next...

10 May 2023 1,970 2 View

Diffusion coefficient calculation easy and way?

Dear all wishes and morning pls reply i need to calculate diffusion coefficient , so 3 electrode or 2 electrode cell which one is easy to calculate from CD or CV or EIS as well as easiest way...

09 March 2023 1,997 3 View

RNA Seq illumina PE reads - Reverse reads (R2) has poor quality?

While trimming the adaptor and low quality RNA-Seq illumina paired end reads in Trimmomatic, I have got more Forward only survive of about 40 to 50%. This study is for estimate the transcript...

28 November 2022 5,770 3 View

How to connect Arduino portenta H7 to transparent OLED screen?

Hey peers! A little guidance can be really helpful here How to connect Arduino Portenta H7 to DFROBOT Fermion 1.51 "OLED transparent display with available breakout board (converter)

02 November 2022 4,950 0 View

Can deep learning be used in signal processing to filter?

I understand that we use butterworth and chebyshev filters to filter out noise etc in signal processing. Can that be substituted by Deep learning?

29 October 2022 7,028 5 View

Which is Suitable machine learning algorithm for weak data (small dataset)?

I have a small dataset. Which machine learning algorithm is suitable for this?

07 January 2021 8,006 8 View

How to convert the pixels into inches in matlab?

i have found the area of segmented image in pixels. How can i convert into inches

01 January 2021 3,865 7 View

How to calculate the area of segment of binary image array in mat lab ?

We have segmented a part from grey scale image using image segmenter (app in mat lab ) and stored as matlab structure. from that structure , how can we calculate the area of the segmented part...

24 December 2020 4,252 3 View

Study design for monitor athletes progress?

What will be the best study design for monitoring athletes progress every 6 months for 3 years. There will be an intervention program after first data collection. No control group or randomized...

10 October 2020 7,417 2 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View