How can I find stress intensity factor in abaqus?

More Asgar Mohamadzadeh's questions See All

Why one of the estimate's parameters, when using the user-defined estimands in Amos, is more than one? Is it acceptable?

Hi everyone! I am testing the total effects of variables using user-defined estimands in Amos for a sample of 410 participants. But one of the estimate's parameters is more than one! Is it...

16 May 2022 7,672 22 View

Which internode length one should take to measure diversity among maize inbred lines?

internode length above the uppermost ear or leaf of the ear or below the ear and if yes, then between which numbers of leaves. Thanks in advance.

02 February 2021 9,011 3 View

Is re-injection of hot mantle magmas can cause re-melting of the partially frozen basalts at the base of the continental crust?

Mafic mantle magmas underplating at the base of the continental arc crust and form the hot zone. These magmas could differentiated to the evolved melts by fractional crystalization and mixing with...

22 August 2016 9,463 4 View

Do basaltic melt could be produced by partial melting of the lower crust?

partial melting usually result in melts with felsic characteristic in comparsion with parent materials.The generation of intermediate to siliceous melts in continental subduction zone by melting...

30 June 2016 488 2 View

What is the density of chlorella microalgae powder?

I want to know about the approximate density of microalgae powder

02 December 2015 7,246 5 View

From where can I purchase microalgae in Iran?

Biodiesel can be produced from some microalgae species that have high lipid content. How can I purchase these microalgae in Iran?

22 October 2015 1,567 5 View

Why do cracks grow in ductile material in curve shape?

for growsing crack of ductile material sem result show front of crack is curve shape. is that becuse plane strain condition is center of plate and plane stress condition on surface? can any one...

12 September 2014 1,636 8 View

Which element is usable for simulating a pre-twisted blade in ansys?

I want to model a twisted blade in ansys and nonlinear dynamic analyses, but solid element is not match with beam element and they are very different result. Now I don't know I select which...

09 September 2014 7,569 3 View

Why can my XFEM method in Abaqus not predict crack grows?

When I use the XFEM method in Abaqus to predict fracture of my materials, Abaqus gives good results about crack initiate and maximum load, but it can't predict crack grows. In Abaqus, after...

16 July 2014 4,325 16 View

Why, in my specimen, do ductile cracks grow and have a smooth surface, when brittle zane is unsmooth?

I take SEM from my specimen. My specimen has 2 zones where one a stable crack grows at 25 C and there is an unstable fracture in liquid nitrogen. I expected that my ductile zone have non smooth...

09 July 2014 5,305 9 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Can anyone provide me with molecular docking softwares/ websites?

Molecular docking software/ websites?

02 August 2024 8,704 7 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View