I am having problems trying to dissolve this dye in ethanol 70% (as part of a protocol) but the process is getting difficut.
Any thoughts?
You may try dissolving in 70% ethanol by warming the solution.
Alternatively dissolve in 100% ethanol and further dilute to 70% adding water.
I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...
28 February 2021 298 3 View
I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...
25 February 2021 2,615 3 View
Currently, I'm working with banana fruits. I've tried to do RNA extractions with different methods, and I've gotten total RNA without contamination, but I couldn't get a high concentration of...
22 February 2021 6,126 2 View
My baseline increases without any explanation, it is only fixed by changing the solution B, will it be the column? Reagents? Bomb? Detector? Solution A: H3PO4 0.01% IN WATER Solution B: H3PO4...
21 February 2021 5,656 3 View
I've got this 5 year Direct Normal Irradiance data I downloaded from https://re.jrc.ec.europa.eu/. I ordered this by year and by every 24 hours because I need the DNI curve by max in summer, min...
17 February 2021 2,777 5 View
Hello everyone I would like to improve the buffer capacity of seawater (pH ~8) in order to dissolve as much CO2 as possible without dropping the pH below 7.5 (a range between 7 - 7.5 is...
17 February 2021 2,797 2 View
I need to design an spiral heat exchanger, buy I don't know what reference or bibliography (preferably a book) should I consult in order to get an updated and reliable methodology related with...
14 February 2021 7,910 3 View
I am looking for a copy of the resume book of UEP2013 Asian Edition (Urban Environmental Pollution 2013 Asian Edition) held in Beijing. If somebody has it, please I would like to obtain an...
11 February 2021 2,247 2 View
Hello there, I'm currently trying to over-express a gene by transfecting the cells with a pcDNA6 plasmid containing my target gene. When I measure the mRNA for my gene of interest, the levels are...
03 February 2021 4,112 4 View
Surely they will want to avoid contact with air/moisture, so what is the procedure for this?
23 January 2021 428 2 View
Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...
24 February 2021 3,785 3 View
23 February 2021 4,014 3 View
I have made neosome from herbal drug. Neosomes are stable. But I face problems in dissolution. I used minimum ratio of 1:1:0.25 ( Drug:span 60: Cholesterol and GMs. Now how can I active better...
17 February 2021 3,584 1 View
I need this solution for my research work. I am facing problem in dissolution of CMC powder
30 December 2020 5,157 2 View
Hi, SO I prepared nano co-crystals and I have done a dissolution study on them, the thing is I'm getting 130% of my co crystals at the end of dissolution which doesn't make sense !! I have...
26 November 2020 8,816 4 View
I prepared a 5X of M9 minimal salt and 1000X elemental trace and mixed these 2 solutions to produce carbon-free minimal salt media. Biphenyl was used as a carbon source but was prepped separately...
20 November 2020 5,904 5 View
Why the pink color will change to yellow, when the DMEM media is frozen? however after dissolution in room temperature, media color will change back into pink.
26 October 2020 708 2 View
Hi, I synthesized the chitosan nanoparticles with encapsulated betaine but the quantity I obtained was much less than expected. I took 20mg betaine and dissolved it in 1ml ethanol because it is...
29 September 2020 8,181 3 View
Hello colleagues, It is known that rapid dissolution of orthopedic implants is dangerous. What methods are used to stop the rate of dissolution of magnesium (its alloy) in physiological...
29 September 2020 1,877 5 View
I use ma-N 2400 resists in my processes to create EBL structures on thick insulating layers (SiO2). Starting from some thickness of SiO2 (about 1 um) I faced the charge issues which completely...
28 September 2020 1,021 3 View