Does anybody have Pdf of Design of the Microelectrode and Modeling of the Brain tissues of MEMS modules in COMSOL 4.1?

07 August 2015 4,309 0 View

Can i simulate experimental work on quantum cascade leser with comsol?

Hello everybody I want to simulate this thesis with COMSOL. (Heat transfer in solid and electromagnetic wave envelope). is it possible? I don't know which Q and T , I should use with what...

04 May 2015 1,336 0 View

How can I solve this error (Failed to find a solution.Singular matrix.Returned solution is not converged.)?

Im working on three modules to gather (semiconductor, electrostatic, heat transfer in solid) for Schottky diode. when COMSOL solve them to gather , has this error: (Failed to find a...

04 May 2015 7,035 4 View

How can i solve two physics togather (electromagnetic wave and heat transfer in solid) in COMSOL5?

Hello everyone, How can i solve two physics togather (electromagnetic wave and heat transfer in solid) in COMSOL5? and which study can solve both of them? thanks alot

04 May 2015 9,725 5 View

Where should I use port in this COMSOL geometry?

04 May 2015 2,898 1 View

Whats does the following error mean in COMSOL: Failed to find consistent initial values?

Hello everybody Im working on plasma, whit helium gas and time-dependent study. its make this error:Failed to find consistent initial values.Last time step is not converged. can anybody help me,...

04 May 2015 1,349 9 View

How can I simulate Second Order Susceptibility?

I want to simulate Second Order Susceptibility, which method and software is better? Thank a lot.

01 February 2015 6,974 0 View

Relative permeability of graphene?

09 October 2014 9,817 11 View

Second harmonics generation - graphene?

07 August 2014 4,585 6 View

What is the refractive index of graphene?

Does anyone know the refractive index of Graphene?

05 June 2014 9,750 1 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

22 February 2021 5,408 1 View