Cytoplasmic staining of BCL-6 in spleen tissue of treated groups rather than nuclear?

I have 3 groups of animal apart from PBS controls where i treat them under different immunosuppressive conditions. when the animals are subjected to partial or no immunosuppressive conditions, i...

31 August 2020 9,012 5 View

In IHC - Alkaline phosphatase method, do we dry the slides or not before mounting in aqueous medium?

In IHC for double staining i use DAB and AP. DAB works fine but AP after mounting is a headache as i see precipitates and also sometimes dissolves.I have tried drying the slides a bit and then...

26 July 2020 219 2 View

How do i use a rabbit monoclonal antibody on rabbit tissues with minimal or no background staining?

I am working with rabbit spleen and as it is difficult to obtain antibodies against rabbits as most of them are raised in rabbits. I had to purchase a few antibodies raised in rabbits. But as...

17 June 2020 3,930 8 View

Background fluorescent staining through different?

I am trying stain for two membrane proteins, one cellular and one viral. But lately, i am doubting a little that the double positive staining could be because of background staining of the other...

19 November 2019 9,633 3 View

I am facing difficulty in immunofluorescence due to autofluorescence?

I am trying out immunofluorescence on rabbit spleen but the results are not fruitful due to auto-fluorescence. I tried blocking with 5%BSA for an hour still persists. I also tried sudan black but...

20 March 2019 1,599 8 View

Do I always need a reference electrode for CV?

I am building a microbial fuel cell. Can I do CV for the full cell without a reference electrode? Do I always need a reference electrode for CV? Or can CV be done using the anode as working...

04 July 2016 5,531 5 View

Can any experts give Pt/c potenital window in alkaline medium?

can any experts give Pt/c potenital window in alkaline medium ?

03 March 2016 2,514 2 View

Can I still consider and amplicon peak with very low fluorescence intensity?

I am standardizing pcr and melt conditions for a particular exon. The fluorescence intensity of my amplificon is low, when compared to my other exons (picture below). Can I consider such melt...

25 November 2014 4,632 3 View

How to test Tensile on single jute fibre and what is standard size of specimen?

01 January 1970 6,081 3 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View